background image

2.  When the lock is disarmed, pressing the bar or paddle will 

open the door instantly without sounding the alarm. Check 
that the lock relatches after 5 seconds. 

3.  Trip the fire-detection or other emergency device with the 

lock armed. Press the bar or paddle and check that the 
latch is released instantly and that the alarm sounds. The 
smoke detector is reset by disarming the lock. 

4. The unit is electrically failsafe. Should any wire open for 

any reason, the exit delay will be eliminated and the door 
may be exited by pressing the bar or paddle. 

 

Low-Battery Indication

 

     A low-battery condition will be indicated by a “chirp” from 

the sounder about once each minute. Be sure to replace 

the battery promptly. An alkaline replacement is strongly 
recommended for optimum reliability and length of 
service. 

 

Lubrication 

     These models are designed to provide many years of 

reliable service when lubricated periodically. Inspect the 
lock on a routine basis in accordance with anticipated use. 
Replenish the factory-applied lubricants at least every five 
years or 25,000 operations, whichever occurs first, using 
the specified lubricants at the points shown in the Wiring 
Diagram.

 

EXPLODED VIEW AND PARTS LIST, MODEL 265 

Summary of Contents for PUSH BAR 715









Reviews: