AL-MEISTER Pluster PLS3311 Instruction Manual Download Page 30 | Manualshive

Page: 30 / 59

background image

AL-MEISTER PLS3311 INSTRUCTION MANUAL <Rev.3>

NOTE CURRENT TEMPERATURE

Press [TEMP/SPEED] to confirm.

The temperature also confirms if [TEMP/SPEED] key is not pressed for 10 sec. The display returns
to the initial display or the warm-up display.

When the set temperature is 140°F, press DOWN scroll key, and the display shows “OFF”.

5-2. SET SPEED

1

Press [TEMP/SPEED] key two (2) times.

This display appears.

NOTE

•

The default is the set speed stored in a microchip in the film core.

2

Press [UP] or [DOWN] scroll key to set speed. Speed can be set by 4”/min increments. The speed
display blinks.

3

Press [TEMP/SPEED] key again to confirm. The speed also confirms if [TEMP/SPEED] key is not
pressed for 10 seconds.

The display returns to the initial display or the warm-up display.

«
...
28
29
30
31
32
...
»

Summary of Contents for Pluster PLS3311




























































Reviews:

No comments

Related manuals for Pluster PLS3311

EXCELAM-1100SWING

Brand: GMP Pages: 39

Brand: ACCO Brands Pages: 21

Brand: Ledco Pages: 30

Brand: Officezone Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands