AL-MEISTER Pluster PLS3311 Instruction Manual Download Page 3

Page: 3 / 59

AL-MEISTER PLS3311 INSTRUCTION MANUAL <Rev.3>

IMPORTANT

The following safety precautions must be observed for your safety during the operation of this product. Please
read the cautions and warnings carefully. Please keep this manual and refer to it whenever necessary.

General Caution

Electric Shock

Indicates possible electric shocks under the specified conditions.

Tangle Warning

Indicates possible injuries caused by tangling in a rotating machine

part.

Amputation Warning

Indicates possible serious injuries such as finger amputation.

Heat Warning

Indicates possible injuries caused by extreme heat.

Don’t do

Indicates unspecified acts that are forbidden.

Unplug immediately

Indicates there may be a dangerous situation that requires you to

unplug the machine immediately.

WARNING AND CAUTION FOR SAFETY

These two different words are used on warning stickers placed on the machine according to the level of danger.

WARNING

・・・

To indicate that incorrect use can cause serious injury.

CAUTION

・・・

To indicate that incorrect use can cause serious injury to the operator or damage to

equipment. There can also be a machine malfunction.

Summary of Contents for Pluster PLS3311




























































Search results

Summary of Contents for Pluster PLS3311

Reviews:

Related manuals for Pluster PLS3311

Brands by name

Popular brands

AL-MEISTER Pluster PLS3311, Instruction Manual

Search results

Summary of Contents for Pluster PLS3311

Reviews:

Related manuals for Pluster PLS3311

Brands by name

Popular brands