background image

Translation of the original operating manual

36

AL-KO

 AIR

CABINET

®

Servicing and maintenance

7.1 

Safety

 WARNING

Risk of fatal electric shock.

There is a risk of a fatal electric shock if live clampings or connections are touched, even when the unit 

is switched off.

 

„

Switch off the unit at the unit main switch.

 

„

Disconnect the unit plug.

 

„

Only open the maintenance panel or the maintenance doors when the unit has cooled 

down and the fans are stationary.

 

„

Wear your PPE (safety shoes, cut-proof gloves).

 WARNING

Risk of injury.

 

„

Disconnect the unit plug before starting any maintenance or repair work on the unit.

 

„

Protect the unit against unauthorised restart.

 

„

Observe the applicable safety rules.

 

„

Have installation, commissioning, maintenance and repair work carried out only by qual-

ified staff!

 

„

Make sure that all factory-fitted safety units are functional before switching the unit on 

again.

 WARNING

Risk of injuries from the run-on of the fan.

 

„

The unit may only by opened by qualified staff or by instructed persons.

 

„

The unit may only be opened when the fan has been switched off and has come to a 

standstill.

 

„

Observe the fan delay time. Wait at least three minutes for the fan impeller to come to a 

standstill before opening the service cover and maintenance panel.

 WARNING

Risk of burn injuries.

 

„

The unit may only be opened by qualified staff or trained persons.

 

„

The unit may only be opened in the shut down and cooled condition.

 

„

Wear your PPE (cut-proof gloves).

 WARNING

Health hazards when removing the filter elements.

 

„

Wear your PPE (FFP2 dust mask) when removing the filters.

 

„

Use further protective equipment according to the work to be carried out (safety shoes, 

gloves).

 

„

Avoid contact with the dust.

Summary of Contents for AIRCABINET

























































Reviews: