AL-KO AIRCABINET Installation And Operating Manual Download

Page: 10 / 56

Translation of the original operating manual

AL-KO

AIR

CABINET

2.1.5 Safety instructions for maintenance

Replace damaged and worn components only with original spare parts.

Always disconnect the unit plug before starting repair and maintenance work.

General maintenance instructions in the Installation and Operating Manual of the AL-KO THERM
GmbH must be observed under all circumstances.

Observe the delay time of the fan. Wait at least three minutes for the fan impeller to come to a
standstill before opening the maintenance panel and the maintenance door.

2.1.6 Personal safety instructions

The

AL-KO

AIR

CABINET

compact air handling unit may only be operated by persons trained in

its use and expressly authorised to do so.

The wearing of PPE is necessary when working on the

AL-KO

AIR

CABINET

compact air han-

dling unit.

The Installation and Operating Manual must be available at a suitable place in the unit operating
location.

2.1.7 Residual dangers

The unit may pose hazards if it is not operated by trained personnel and/or is operated improperly or

not according to its intended use.

Residual dangers are potential hazards that are not immediately apparent, such as:

Injuries due to failure to observe the safety instructions, standards, directives or regulations.

Injuries caused by uncoordinated work.

Injuries or death from electric shock due to working on cables with damaged insulation and de-
fective connections.

Risk of fire hazard due to damaged fan parts, e.g. hot-running bearings.

Injuries caused by working on the fan before it has come to a standstill.

Injuries caused by pinching or crushing and collisions during transport, unpacking and setup of
the unit.

Tipping of the unit due to installation on uneven or loose ground.

Risk of tripping and falling due to improper routing of the electrical connecting lead.

Health hazards due to poor hygiene, such as failure to change filters at regular intervals.

Hazards due to misconduct resulting from failure to observe the safety instructions, standards

and regulations.

Summary of Contents for AIRCABINET

























































Search results

Summary of Contents for AIRCABINET

Reviews:

Related manuals for AIRCABINET

Brands by name

Popular brands

AL-KO AIRCABINET, Installation And Operating Manual

Search results

Summary of Contents for AIRCABINET

Reviews:

Related manuals for AIRCABINET

Brands by name

Popular brands