Akw SmartCare Plus Installation And Instruction Manual Download Page 5

Page: 5 / 36

13-012-085-17

User

Starting the Shower

Switch on the mains power at the isolating switch.

When power is applied, the inner light ring will be dimly lit and the shower is in standby

mode.

To switch on, press the power button. The inner light ring will be brightly lit.

The outer light ring will now indicate Temp/Flow settings (mode dependent)

Temperature and Flow Setting

Pressing and releasing

Temp (+)

increases outlet water temperature

Temp (-)

decreases outlet water temperature

Flow (+)

increases outlet water flow rate

Flow (-)

decreases outlet water flow rate

NOTE:

Changes in the flow rate and water temperature may take a few seconds to reach the

handset.

Temp Increase

Flow Increase

Inner Light Ring

Outer Light Ring

Flow Decrease

Temp Decrease

Operating Instructions

Summary of Contents for SmartCare Plus





































Search results

Summary of Contents for SmartCare Plus

Reviews:

Related manuals for SmartCare Plus

Brands by name

Popular brands

Akw SmartCare Plus, Installation And Instruction Manual

Search results

Summary of Contents for SmartCare Plus

Reviews:

Related manuals for SmartCare Plus

Brands by name

Popular brands