Akiyama DX-101 USB-R Instruction Manual Download Page 5

4

17. HEADSHELL

 - Install cartridge here. When installing a cartridge, refer to the 

installation instructions supplied by the manufacturer of that cartridge. During 
installation, attach the stylus protector to guard the stylus tip from damage.
Attach wires as follows:
White (L+)     Left
Blue (L-)        Left channel -
Red (R+)        Right
Green (R-)      Right channel-

18. S-SHAPED TONE ARM

19. TONE ARM LEVER  

Controls the up and down action of the tone arm lift.

20.ANTI-SKATE CONTROL

  This applies inward force to the tone arm so it 

doesn't skip outward across the record due to the centrifugal force of the record 
spinning. Cartridge manufacturers usually specify the proper setting of this.

21. COUNTERWEIGHT  

Adjustment creates the proper downward pressure of 

the stylus to the record. Attach now by sliding the counterweight onto the rear of the 
tone arm. Twist it lightly and it will screw onto the rear shaft of the tone arm.

TONE ARM ASSEMBLY

1.

 Push the power to on and the speed indicator and the stylus 

9.

 Set the cueing lever to the down position, the tone arm will descend 

illuminator will light up.

slowly onto. 

The record and play begins.

2.

 Insert target light for illumination the stylus.

10. 

Set the desired pitch adjusts range by depressing the buttons until 

3.

 Place a record on the turntable mat. When playing a 45rpm record 

the desired pitch is reached.

with a large centre hole; place the 45rpm adapter on the centre 

Options are +/-10%.

spindle.

11.

 Adjust the pitch to a desirable speed. 

4.

 Set the rotation speed (33/45/78) to match the record.

12. 

To suspend play, lift tone arm with cueing lever.

5

. Release the arm clamp.

13.

 When play is finished, raise the cueing lever, move the tone arm to 

6.

 Set the cueing lever to the up position.

the armrest and secure the tone arm with the arm clamp.

7.

 Press the Start/Stop button and the turntable platter will start to 

14.

 Press the Start/Stop button to stop the platter rotating.

rotate.

15.

 Push the  power to off.

8.

 Move the tone arm over the desired groove.

OPERATION

21

19

18

20

17

 dx turntables

 e

ng

li

sh

Summary of Contents for DX-101 USB-R












Reviews: