manualshive.com logo in svg

AkitikA PR-101, Assembly Manual, Page: 7 / 21

Share
Download
AkitikA PR-101 Assembly Manual Download Page 7

Page 7 of 21 

Component Order 

 

You’ll notice that the component designations in the directions don’t go in order. We 
have grouped them so that all components with the same value appear together. This 
makes assembly easier. You’ll find in the parts kit that similar parts, e.g. 3 1K resistors, 
are typically (though not always) taped together. 

Install the Resistors 

In general, you install axial leaded components (like the resistors) by placing the body on 
the silk screen side of the board, and the leads through the indicated holes. Bend the leads 
over on the back of the board to keep the resistors from falling out until your solder them 
in place. Try to bend the leads in a direction that won’t lead to solder bridges between 
traces that should remain disconnected. 
 
We recommend the following procedure: 

1.

 

Insert all components of the same value or type 

2.

 

Bend the leads as described above. 

3.

 

Solder the leads on the back of the board. 

4.

 

Clip the leads. 

Track your progress by placing a check-mark in the done column as you install each 
component. 

Bend resistor leads to 0.45” width 

Designation Value 

Color 

Code 

Done 

 

R21 

100 

Brown, Black, Black, Black, Brown 

 

R1 

200 

Red, Black, Black, Black, Brown 

 

R2 

200 

Red, Black, Black, Black, Brown 

 

R5 

200 

Red, Black, Black, Black, Brown 

 

R6 

200 

Red, Black, Black, Black, Brown 

 

R8 

200 

Red, Black, Black, Black, Brown 

 

R12 

200 

Red, Black, Black, Black, Brown 

 

R13 

200 

Red, Black, Black, Black, Brown 

 

R14 

200 

Red, Black, Black, Black, Brown 

 

R3 

10K0 

Brown, Black, Black, Red, Brown 

 

R4 10K0 

NO 

LOAD 

 

R7 

10K0 

Brown, Black, Black, Red, Brown 

 

R9 

10K0 

Brown, Black, Black, Red, Brown 

 

R10 

10K0 

Brown, Black, Black, Red, Brown 

 

R11 10K0 

NO 

LOAD 

 

R15 

10K0 

Brown, Black, Black, Red, Brown 

 

R16 

10K0 

Brown, Black, Black, Red, Brown 

 

R17 

100K 

Brown, Black, Black, Orange, Brown 

 

R18 

100K 

Brown, Black, Black, Orange, Brown 

 

R22 

1M00 

Brown, Black, Black, Yellow, Brown 

 

Save two pieces of the clipped resistor lead. Depending upon the gain setting you choose, 
they may be used in the next section. 

Summary of Contents for PR-101






















Reviews:

No comments