manualshive.com logo in svg

AkitikA PR-101, Assembly Manual, Page: 2 / 21

Share
Download
AkitikA PR-101 Assembly Manual Download Page 2

Page 2 of 21 

Table of Contents 

Table of Contents................................................................................................................ 2 
Table of Figures .................................................................................................................. 3 
Section 1: About This Manual ............................................................................................ 4 

Who Should Attempt this Project? ................................................................................. 4 
Tools you’ll need ............................................................................................................ 4 
Helpful Tools .................................................................................................................. 4 
Project Overview ............................................................................................................ 4 
Important Safety Notes ................................................................................................... 5 
About Components ......................................................................................................... 5 
Recommended Solder ..................................................................................................... 5 
Warranty ......................................................................................................................... 5 

Section 2: Kit Building Hints.............................................................................................. 6 
Section 3: Building the Headphone Amp ........................................................................... 6 

Component Order............................................................................................................ 7 
Install the Resistors ......................................................................................................... 7 
Selected Resistor Installation.......................................................................................... 8 
Install the diodes ............................................................................................................. 8 
Install the small non-polarized capacitors....................................................................... 9 
Install the bypass capacitors............................................................................................ 9 
Install the Integrated Circuits.......................................................................................... 9 
Install the Electrolytic (polarized) Capacitors .............................................................. 10 
Install the Relays, Transistors, and MOSFET .............................................................. 10 

Section 4: Install the Wires ............................................................................................... 10 

Power and Ground Wires.............................................................................................. 10 

12 Volt Ground wires................................................................................................ 10 
12 Volt Power wires.................................................................................................. 11 

Install the Signal Wires................................................................................................. 12 

Signal Input Wires .................................................................................................... 12 
Signal Output Wires.................................................................................................. 13 

Section 5 – Install the Headphone Amp into the PR-101 ................................................. 14 

Mechanical Installation................................................................................................. 14 

Dismount the tone/volume board.............................................................................. 14 
Mount the Headphone Amp Board ........................................................................... 15 

Wiring the Headphone Amp In..................................................................................... 15 

Headphone Jack Connections ................................................................................... 15 
Power Wiring ............................................................................................................ 16 
Reinstall the Tone/Volume Board ............................................................................ 17 
Signal Connections ................................................................................................... 17 

Section 6: Tests and Final Assembly ................................................................................ 18 
Section 7: About the Headphone Preamp ......................................................................... 18 

Specifications................................................................................................................ 18 
Revision Notes .............................................................................................................. 19 

Appendix 1 – Shielded Cable Preparation ........................................................................ 20 

Summary of Contents for PR-101






















Reviews:

No comments