AKDY 10A3(IS)-30 Installation Instructions And Use & Care Manual Download Page 13 | Manualshive

Page: 13 / 20

background image

13

INSTALL RANGE HOOD

1. Using 2 or more people lift the range hood assembly and attach it to the upper support frame.

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

2. Install M4*12 screws on both side and tighten to secure.

3. Plug in the power supply cable.

«
...
11
12
13
14
15
...
»

Summary of Contents for 10A3(IS)-30





















Reviews:

No comments

Related manuals for 10A3(IS)-30

Brand: La Cornue Pages: 24

Brand: La Cornue Pages: 19

Brand: V-ZUG Pages: 3

Brand: NEFF Pages: 96

RNHP30 Renaissance

Brand: Dacor Pages: 33

Brand: BOMANN Pages: 28

Brand: THERMEx Pages: 60

Brand: Broan Pages: 12

Brand: Robam Pages: 12

CLASSICA PLUS CLPL30SSV

Brand: Faber Pages: 44

Brand: INOXPAN Pages: 40

Brand: Futuro Futuro Pages: 2

Brand: Auscrown Pages: 7

Brand: Siemens Pages: 64

Brand: Hafele Pages: 36

Brand: ETNA Pages: 42

Brand: CONSTRUCTA Pages: 52

Brand: CONSTRUCTA Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands