AJA KONA 4 Installation And Operation Manual Download

Page: 65 / 89

KONA Capture, Display, Convert v15.2 65 www.aja.com

HDMI HDR Screen in 4K Mode

Figure 42. HDMI HDR Screen with 4K Primary Format

The HDMI-HDR screen, available in KONA 5 the 4K mode of KONA 4, provides

a mechanism to inform an HDMI display device (such as a TV or monitor) that

the video content is HDR. This includes generation of the Dynamic Range and

Mastering Infoframe and the static metadata descriptors as defined in CTA-861.3

and HDMI v2.0a. Included are pre-defined primaries values for BT.2020 and DCI P3

color gamuts.

HDR Mode

• Off - HDR Mode disabled (default).
• DCI-P3 D65 - Only Display Mastering Luminance available for Digital

Primaries.

• BT.2020 - Typically used with HDR.
• Custom - Allows custom values for the Digital Primaries.

EOTF

The Electrical Optical Transfer Function metadata bit tells the HDMI display which

EOTF to use. Most TV’s will require this to be set to ST 2084 for their HDR modes.

•  Trad Gamma SD
•  Trad Gamma HD
•  ST 2084 (HDR-10)
•  HLG (Hybrid Log Gamma) - No meta-data for Digital Primaries.

Summary of Contents for KONA 4


























































































Search results

Summary of Contents for KONA 4

Reviews:

Related manuals for KONA 4

Brands by name

Popular brands

AJA KONA 4, Installation And Operation Manual

Search results

Summary of Contents for KONA 4

Reviews:

Related manuals for KONA 4

Brands by name

Popular brands