background image

speaker terminals.

• Dynamic Bass System
TS-W60 adopts a Dynamic Bass System in which port (1), duct (1), and air cavity (2) compose an acoustic bandpass
filter in front of air cavity (1). By virtue of this structure, the bass reproduction limit is extended and sounds higher
than middle range frequencies are reduced in the Dynamic Bass System. This makes it possible for the TS-W60 to
reproduce powerful bass sound.

pg. 4

PRECAUTIONS

Follow the advice below for safe and correct operation.

ON AC voltage
Before connecting AC cord, check that the rated voltage shown on the rear panel matches your local voltage.
AC 120 V, 60 Hz

Positioning
•  Do not use the unit in places which are extremely hot, cold, dusty or humid.
•  The unit should be situated with adequate space around it so that proper heat ventilation is assured. Allow 10 cm
clearance from the rear and the top of the unit, and 5 cm from the each side.
- Do not place the unit on a bed, rug, or similar surface that may block the ventilation openings.
- Do not install the unit in a bookcase, cabinet, or airtight rack where ventilation may be impeded.

Using the unit near a TV set
Although the unit is magnetically shielded, there may be cases in which the picture on some TV sets may become
magnetically distorted.
• If the TV picture is distorted, turn off the power of the TV set once, and after 15 to 30 minutes turn it on again.
• If there seems to be no improvement, move the unit further away from the TV set.
• Furthermore, be sure not to place magnets or objects using magnets, such as audio racks, toys etc. near the TV set.
These may cause magnetic distortion to the picture due to their interaction with the unit.

Howling or buzzing sound
A howling or buzzing sound may be heard if a turntable or a stereo system is placed near the unit. Move the unit
away from the equipment or decrease the volume.

Summary of Contents for TS-W60








Reviews: