manualshive.com logo in svg

AISWEI ASW1000S-S, Installation And Operating Instructions Manual

Share
Download
AISWEI ASW1000S-S Installation And Operating Instructions Manual Download Page 48

  48

                                                                           

Installation  and  Operating  Instructions

 

V00

 

 

 

⑤

 Check the grid voltage: check that the grid voltage at the point of connection of the 

inverter complies with the permitted value. 

8.2 Mechanical checks 

Carry out the main mechanical checks to ensure the inverter is waterproof: 

①

 Make sure the inverter has been correctly mounted with wall bracket. 

②

 Make sure the cover has been correctly mounted. 

③

 Make sure the communication cable and AC connector have been correctly wired 

and tightened. 

 

8.3 Safety code check 

Choose suitable safety code according to the location of installation. please visit website 
(

http://www.aisweicloud.com

 

) and download the AISWEI Cloud APP manual for detailed 

information, you can find the Safety Code Setting Guide in an event where an installer 
needs to set the country code manually. 

 

 

 

 

 

Danger to life due to the presence of AC voltage 

• Only touch the insulation of the AC cables.

 

• Wear personal protective equipment such as insulating gloves.

 

 

 

Information for safety code

 

• The Solplanet’s inverters comply wit l

ocal safety code when leaving 

the factory.

 

Summary of Contents for ASW1000S-S






































































Reviews:

No comments

Brands by name

Popular brands

Load more brands