manualshive.com logo in svg

AISWEI ASW1000S-S, Installation And Operating Instructions Manual

Share
Download
AISWEI ASW1000S-S Installation And Operating Instructions Manual Download Page 36

  36

                                                                           

Installation  and  Operating  Instructions

 

V00

 

6 Communication 

6.1 System monitoring via RS485/ Ethernet 

This inverter is equipped with RJ45 interfaces for multipoint communication. 
One AiCom/AiManager connects inverters via an RS485 bus. The overall length of the 
network cable should not exceed 1,000 m. The monitoring system layout for 
inverters is as follows. 
 

 

The AiCom/AiManager connects to the inverter via the RJ45 interface, and it connects 
to the router via Ethernet.User can monitor the inverter through

 the external 

AiCom/AiManager

 with Ethernet module (optional),   

 

 

The inverter is connected to the network by simply connecting the network cable 
from the router to the Ethernet port on the 

AiCom/AiManager

. For connecting the 

network cable, please refer to the relative instruction at section 6.1.   

 

 

Possible reason of communication failure due to closed port 

• 

The AiCom/AiManager uses port #1883 and #80 communicates with the 

AISWEIcloud. Both of these two ports must be opened, or else the 
AICom/AiManager cannot connect to the AiSWEIcloud and upload data. 

 

Summary of Contents for ASW1000S-S






































































Reviews:

No comments

Brands by name

Popular brands

Load more brands