background image

INSTALLATION MANUAL

INDOOR UNIT (Wall Mounted Type: EEV internal)

For authorized service personnel only.

PART NO. 9373370192

INSTALLATIONSANLEITUNG

INNENGERÄT (wandmontierter Typ: EEV intern)

Nur für autorisiertes Fachpersonal.

ASYA04GACH/ASHA04GACH
ASYA07GACH/ASHA07GACH
ASYA09GACH/ASHA09GACH
ASYA12GACH/ASHA12GACH
ASYA14GACH/ASHA14GACH

TM

MANUEL D’INSTALLATION

MANUAL DE INSTALACIÓN

APPAREIL INTÉRIEUR (Type montage mural : interne EEV)

UNIDAD INTERIOR (Tipo montado en pared: EEV interna)

Pour le personnel agréé uniquement.

Únicamente para personal de servicio autorizado.

MANUALE DI INSTALLAZIONE

UNITÀ INTERNA (tipo montato a parete: EEV interno)

A uso esclusivo del personale tecnico autorizzato.

ΕΓΧΕΙΡΙΔΙΟ

 

ΕΓΚΑΤΑΣΤΑΣΗΣ

ΕΣΩΤΕΡΙΚΗ

 

ΜΟΝΑΔΑ

 (

Επιτοίχιος

 

Τύπος

ΗΕΒ

 

εσωτερικά

)

Μόνο

 

για

 

εξουσιοδοτημένο

 

τεχνικό

 

προσωπικό

.

MANUAL DE INSTALAÇÃO

UNIDADE INTERIOR (Tipo mural: modelo interno com EEV)

Apenas para técnicos autorizados.

РУКОВОДСТВО

 

ПО

 

УСТАНОВКЕ

ВНУТРЕННИЙ

 

МОДУЛЬ

 (

настенного

 

типа

внутренний

 

электронный

 

расширительный

 

клапан

)

Только

 

для

 

авторизованного

 

обслуживающего

 

персонала

.

MONTAJ KILAVUZU

İ

Ç ÜN

İ

TE (Duvara Monteli Tip: EEV dahili)

Yaln

ı

zca yetkili servis personeli için.

English

Deutsch

Français

Español

Italiano

Ελληνικ

ά

Português

Ру

сский

Türkçe

9373370192_IM.indb   1

9373370192_IM.indb   1

2/16/2013   11:12:27 AM

2/16/2013   11:12:27 AM

Summary of Contents for ASHA04GACH
















Reviews: