En-1
1. SAFETY PRECAUTIONS
• Be sure to read this Manual thoroughly before installation.
• The warnings and precautions indicated in this Manual contain important information
pertaining to your safety. Be sure to observe them.
• Hand this Manual, together with the Operating Manual, to the customer. Request the
customer to keep them on hand for future use, such as for relocating or repairing the
unit.
WARNING
This mark indicates procedures which, if improperly performed,
might lead to the death or serious injury of the user.
Request your dealer or a professional installer to install the indoor unit in accordance
with this Installation Manual. An improperly installed unit can cause serious accidents
such as water leakage, electric shock, or
fi
re. If the indoor unit is installed in disregard
of the instructions in the Installation Manual, it will void the manufacturer’s warranty.
Do not turn ON the power until all work has been completed. Turning ON the power
before the work is completed can cause serious accidents such as electric shock or
fi
re.
If refrigerant leaks while work is being carried out, ventilate the area. If the refrigerant
comes in contact with a
fl
ame, it produces a toxic gas.
Installation work must be performed in accordance with national wiring standards by
authorized personnel only.
Except for EMERGENCY, never turn off main as well as sub breaker of the indoor units
during operation. It will cause compressor failure as well as water leakage. First, stop
the indoor unit by operating the controller, converter or external input device and then
cut the breaker.
Make sure to operate through the controller, converter or external input device.
When the breaker is designed, locate it at a place where the users cannot start and
stop in the daily work.
CAUTION
This mark indicates procedures which, if improperly performed,
might possibly result in personal harm to the user, or damage to
property.
Read carefully all security information before use or install the air conditioner.
Do not attempt to install the air conditioner or a part of the air conditioner by yourself.
This unit must be installed by quali
fi
ed personnel with a capacity certi
fi
cate for handling
refrigerant
fl
uids. Refer to regulation and laws in use on installation place.
The installation must be carried out in compliance with regulations in force in the place
of installation and the installation instructions of the manufacturer.
This unit is part of a set constituting an air conditioner. It must not be installed alone or
with non-authorized by the manufacturer.
Always use a separate power supply line protected by a circuit breaker operating on all
wires with a distance between contact of 3mm for this unit.
The unit must be correctly grounded and the supply line must be equipped with a
differential breaker in order to protect the persons.
The units are not explosion proof and therefore should not be installed in explosive
atmosphere.
Never touch electrical components immediately after the power supply has been turned
off. Electric shock may occur. After turning off the power, always wait 5 minutes before
touching electrical components.
This unit contains no user-serviceable parts. Always consult authorized service
personnel to repairs.
When moving, consult authorized service personnel for disconnection and installation
of the unit.
2. ABOUT THE UNIT
1
2.1. Precautions for using R410A refrigerant
WARNING
Do not introduce any substance other than the prescribed refrigerant into the
refrigeration cycle. If air enters the refrigeration cycle, the pressure in the refrigeration
cycle will become abnormally high and cause the piping to rupture.
If there is a refrigerant leak, make sure that it does not exceed the concentration limit.
If a refrigerant leak exceeds the concentration limit, it can lead to accidents such as
oxygen starvation.
Do not touch refrigerant that has leaked from the refrigerant pipe connections or other
area. Touching the refrigerant directly can cause frostbite.
If a refrigerant leak occurs during operation, immediately vacate the premises and
thoroughly ventilate the area. If the refrigerant comes in contact with a flame, it
produces a toxic gas.
]1
2.2. Special tool for R410A
WARNING
To install a unit that uses R410A refrigerant, use dedicated tools and piping materials
that have been manufactured specifically for R410A use. Because the pressure
of R410A refrigerant is approximately 1.6 times higher than the R22, failure to
use dedicated piping material or improper installation can cause rupture or injury.
Furthermore, it can cause serious accidents such as water leakage, electric shock, or
fi
re.
Tool name
Changes
Gauge manifold
The pressure in the refrigerant system is extremely high
and cannot be measured with a conventional gauge. To
prevent erroneous mixing of other refrigerants, the diameter
of each port has been changed. It is recommended to use a
gauge manifold with a high pressure display range of –0.1
to 5.3 MPa and a low pressure display range of –0.1 to 3.8
MPa.
Charging hose
To increase pressure resistance, the hose material and
base size were changed.
(The charging port thread diameter for R410A is 1/2 UNF
20 threads per inch.)
Vacuum pump
A conventional vacuum pump can be used by installing a
vacuum pump adapter.
Be sure that the pump oil does not back
fl
ow into the sys-
tem. Use one capable for vacuum suction of –100.7 kPa (5
Torr, –755 mmHg).
Gas leakage detector
Special gas leakage detector for R410A refrigerant.
INSTALLATION MANUAL
PART NO. 9367701100
VRF system indoor unit (Floor / Ceiling type)
Contents
1. SAFETY
PRECAUTIONS
........................................................................................ 1
2. ABOUT THE UNIT ................................................................................................... 1
2.1. Precautions for using R410A refrigerant ............................................................... 1
2.2. Special tool for R410A ....................................................................................... 1
2.3. Accessories ....................................................................................................... 2
2.4. Optional parts .................................................................................................... 2
3. INSTALLATION
WORK
........................................................................................... 2
3.1. Selecting an installation location ....................................................................... 2
3.2. Installation dimension ........................................................................................ 3
3.3. Installation the unit ............................................................................................. 3
4. PIPE
INSTALLATION
............................................................................................... 4
4.1. Selecting the pipe material ................................................................................ 4
4.2. Pipe requirement ............................................................................................... 5
4.3. Flare connection (pipe connection) ................................................................... 5
4.4. Installing heat insulation .................................................................................... 6
5. INSTALLING DRAIN HOSE ..................................................................................... 6
6. ELECTRICAL
WIRING
............................................................................................. 7
6.1. Electrical requirement ........................................................................................ 7
6.2. Wiring method ................................................................................................... 8
6.3. Unit wiring .......................................................................................................... 8
6.4. Connection of wiring ......................................................................................... 9
6.5. External input and external output (Optional parts) ........................................... 9
7. FIELD
SETTING
..................................................................................................... 11
7.1. Setting the address .......................................................................................... 11
7.2. Custom code setting ........................................................................................ 12
7.3. Switching the upper limit of cooling temperature ................................................... 12
7.4. Function setting ............................................................................................... 12
8. MOUNT THE COVER PLATE AND THE INTAKE GRILLE ................................... 14
8.1. Handling for the pipe take-off part ................................................................... 14
8.2. Mount the cover plate (Right) .......................................................................... 14
8.3. Mount the cover plate (Left) ............................................................................. 14
8.4. Mount the intake grille ..................................................................................... 14
9. TEST
RUN
.............................................................................................................. 15
9.1. Test run using Outdoor unit (PCB) .................................................................. 15
9.2. Test run using remote controller ...................................................................... 15
10. CHECK LIST
.......................................................................................................... 15
11. ERROR
CODES
..................................................................................................... 15
9367701100-01_IM.indb Sec1:1
9367701100-01_IM.indb Sec1:1
2012-7-12 14:01:30
2012-7-12 14:01:30
