background image

 AirUnity 545 eNB 2.5GHz (B41) User Guide  

UGD-D01127

 

Airspan Commercial and Internal Use 

23 

A  Abbreviations 

Term 

Expansion 

3GPP 

3rd Generation Partnership Project, responsible for LTE 

AV-eNB 

AirVelocity eNodeB 

BER 

Bit Error Rate 

CN 

Core Network 

CP 

Cyclic Prefix 

dB 

Decibel. A logarithmic unit used to describe a ratio (such as power ratio in 
radio telecommunications) 

dBm 

An abbreviation for the power ratio in decibels (dB) of the measured power 
referenced to one milliwatt (mW). It is used as a convenient measure of 
absolute power because of its capability to express both very large and very 
small values in a short form 

DL 

Downlink 

EMS 

Element Management System 

eNodeB 

Evolved Node B, is the element in E-UTRAN of LTE 

ESP 

Encapsulating Security Payloads (ESP) provide confidentiality, data-origin 
authentication, connectionless integrity, an anti-replay service (a form of 
partial sequence integrity), and limited traffic-flow confidentiality 

E-UTRAN 

Evolved Universal Terrestrial Radio Access Network, is the air interface of 
3GPP's Long Term Evolution 

FDD 

Frequency-Division Duplexing. A transceiver mode where the transmitter and 
receiver operate at different carrier frequencies 

GPS 

Global Positioning System 

IPsec 

Internet Protocol Security is a protocol suite for securing Internet Protocol 
(IP) communications by authenticating and encrypting each IP packet of a 
communication session 

LED 

Light Emitting Diode 

LTE 

Long Term Evolution 

MAC 

Medium Access Controller 

– responsible for several functions such 

Scheduling, Packet (De) Multiplexing, etc… 

MCS 

Modulation and Coding Scheme  

MIMO 

Multiple-Input Multiple-Output 

MME 

Mobility Management Entity is the key control-node for the LTE access-
network. It is responsible, among other things for idle mode UE tracking and 
paging procedure including retransmissions 

MTBF 

Mean Time Between Failures 

OFDMA 

Orthogonal Frequency-Division Multiple Access (OFDMA) is a multiple 
access version of OFDM digital modulation scheme, used for eNodeB 
transmissions to UEs 

PDCP 

Packet Data Convergence Protocol. A Sub-Layer in LTE responsible for 
Security, IP Header (De) Compression, etc… 

PTP 

Precision Time Protocol is used to synchronize clocks throughout a network. 
In this document, PTP is referring to IEEE1588-2008 protocol 

QAM 

Quadrature Amplitude Modulation 

QPSK 

Quadrature Phase Shift Keying 

RB 

Resource Block 

RLC 

Radio Link Control. A Sub-Layer in LTE responsible for Ack/Nack, error 
correction, packet reordering, etc… 

ROHS 

Restriction Of Hazardous Substances 

RRC 

Radio Resource Control. A Sub-Layer in LTE responsible for Broadcast of 
system information, paging, security functions, radio bearer control, etc… 

RRM 

Radio Resource Management is used to cover all functions that are related 
to the assignment and sharing of radio resources among UEs 

SC-FDMA 

Single-Carrier FDMA is a frequency-division multiple access scheme, dealing 
with the assignment of multiple users to a shared communication resource. 
Used in LTE for UE transmissions to the eNodeB 

SDR 

Software Defined Radio 

TDD 

Time-Division Duplexing. A transceiver mode where the transmitter and 
receiver operate on the same carrier frequency 

UE 

User Equipment. The end user in LTE 

Summary of Contents for AirUnity 545 eNB B41





























Reviews: