AirPower Chinook K100 Reconditioning Manual Download Page 25 | Manualshive

Page: 25 / 26

background image

Disassemble filter to clean. Wash breather with oil solvent. Correct oil level is centre of oil sight glass
or to top of sight glass. Do not fill higher than top of sight glass. Do not run lower than sight glass.
Oil capacities:
Model          litres
K8                 0.355
K11               0.5
K12               0.5
K17               1.0
K18               1.0
K24               1.8
K25               1.8
K28               1.8
K30               1.39
K35               1.39
K50               1.75
K60               2.9
K100             4.0

-24-

«
...
23
24
25
26
»

Summary of Contents for Chinook K100



























Reviews:

No comments

Related manuals for Chinook K100

Brand: Jacuzzi Pages: 8

Brand: Raypak Pages: 40

Brand: Sanden Pages: 48

BlackFin CT-2902BPHP

Brand: Panduit Pages: 68

Brand: Waterax Pages: 6

Brand: Panduit Pages: 7

Brand: Texas Equipment Pages: 11

Brand: Asada Pages: 28

Brand: Barnes Pages: 27

Brand: GE Pages: 20

Brand: Raider Pages: 78

Brand: BOC Edwards Pages: 62

Kempion PKD Series

Brand: Cheonsei Pages: 32

Brand: Nakayama Pages: 33

Brand: vacuubrand Pages: 96

Brand: Trotec Pages: 18

Pneumatic Oilpump 3:1

Brand: Pressol Pages: 28

NCE H 25-100/180

Brand: Calpeda Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands