AirMan SDG40S-8B1 Instruction Manual Download Page 17

Page: 17 / 69

3. Installation

A050507-1



The machine should be operated in following conditions:



Ambient temperature

5°F to 104°F(

-15

℃～＋

℃

)



Humidity

Less than 85%



Altitude

Lower than 500 m above sea level



If more than two machines are placed parallel in
operation, keep enough distance so that exhaust air
from one machine does not effect the other one.



Keep enough space around the unit for inspection and
maintenance access.



In order to prevent from entering the jobsite or touching
the equipment any other persons than the persons
engaged in the job, please prepare for safety fences
around the unit:

1000 or more

00 or mor

SG0110

Unit : mm

Preparation of safety fences

Safety fences

Discount-Equipment.com

Summary of Contents for SDG40S-8B1






































































Search results

Summary of Contents for SDG40S-8B1

Reviews:

Related manuals for SDG40S-8B1

Brands by name

Popular brands

AirMan SDG40S-8B1, Instruction Manual

Search results

Summary of Contents for SDG40S-8B1

Reviews:

Related manuals for SDG40S-8B1

Brands by name

Popular brands