AirMan SDG100S-8B1 Instruction Manual Download Page 42

5. Periodic Inspection/Maintenance

 

 

5

-

1

5.1    Important Items at Periodic Inspection and Maintenance or after 

Maintenance

 

 

The manual shows proper interval for periodic inspection and maintenance under normally 
operating conditions. Inspection and maintenance should be performed more often under extremely 
harsh conditions

 
 
 

 

Remove the starter key from the starter switch before 
starting inspection, and hang up a “Now Checking and 
under Maintenance” tag where it can be easily seen. The 
checker must keep the key during checking and 
maintenance. 

 

Remove the negative (-) side cable from the battery. If the 
above procedure is neglected, and should another person 
start operating the machine during check or maintenance, it 
could cause serious injury. 

 

Be sure to use appropriate tools for inspection and 
maintenance work. Inappropriate tools could cause 
unexpected injury.

 

 
 
 
 

 

Be sure to use recommended fuel, oil, grease, or antifreeze. 

 

Do not disassemble or adjust engine, compressor or part(s) for which inspection or maintenance is not 
referred to in this manual. 

 

Use genuine parts for replacement. 

 

Any breakdown, caused by using unapproved parts or by wrong handling, will be out of the scope of 
“WARRANTY”. 

 

Do not pour water or steam on electrical components. 

 

Place a container or a pan underneath the oil port to receiver waste liquid so that such liquid cannot be 
spilt out on the floor or inside the machine. 

 

Be sure that no waste liquid is disposed of on the ground. Such waste on the ground, river or lake will 
cause serious environmental contamination. Be sure to follow the local regulations. If harmful material 
such as oil, antifreeze solution or filters are disposed of incorrectly, the responsible person should be 
punished by the authority. 

 

Observe local regulations when disposing of such toxic materials as oil, fuel, coolant (anti-freeze), filters, 
and battery etc. 

 

SY001

Hang a

Now Checking and under Maintenance

tag

 

Precaution for check and maintenance

 

Discount-Equipment.com

Summary of Contents for SDG100S-8B1












































































Reviews: