AirMaid 10000V Installation, Operation And Maintenance Manual Download Page 3

2

3

WARNINGS AND SAFETY CONSIDERATIONS

General

This installation and service guide contains important instructions and safety information for the AirMaid® Ozone 

Generator (hereafter referred to as ”The Generator”).  Read this guide fully before attempting to install, operate, or 

perform maintenance on The Generator. 

The Generator is for commercial use and intended for the treatment of air extracted from the exhaust ducts of new 

or existing commercial kitchens and building ventilation systems that exhaust to the outdoors. The completed 

installation must meet all local, state and national building, electric and fire safety codes.

A typical installation into a commercial kitchen exhaust duct is described. Other applications for treating extraction air 

may also be possible, but only for air which is released into the outside environment and never into working or living 

spaces. In all cases, the specific requirements according to this guide must be fulfilled.  

The device may not be used by children or by persons with diminished physical, sensory or mental capacity or lack 

of experience and knowledge unless supervised or having received instruction. Supervise children to ensure that 

they do not play with the device.

Always disconnect the electric power source from The Generator before performing any service or maintenance.

The Generator, alarm panel and connections to inlet air and extraction ducts must be installed by qualified per-

sonnel, in compliance with all manufacturer instructions as well as local, state and national building,  

electric and fire safety codes.

Troubleshooting & Requesting Service 

In the event of operational difficulties with The Generator please contact your distributor or Interzon Technical 

Support.  

Repairs must only be performed by Interzon-trained and authorized service personnel unless prior written consent 

has been given. Only original repair parts provided by the manufacturer may be used when servicing The Generator.

If damage has occurred during shipping, notify the freight carrier at once so that a claim can be filed with the carrier.

This equipment is heavy! See product specifications for rated weight. Always exercise extreme caution 

when mounting or dismounting The Generator to assure it cannot be dropped. Use only approved work 

platforms to access The Generator. Never stand on cooking equipment as falls can result in serious inju-

ries. Wear industry-prescribed work clothing, gloves and eye protection while mounting, dismounting or 

servicing The Generator.  

Electrical Shock Hazard! Disconnect power before servicing. Replace all parts and panels before operating. 

Failure to do so can result in electrical shock, burns or death.

 This unit emits low levels of ozone into the exhaust duct. If improperly used by unqualified personnel 

extended exposure to ozone can result in irritation to eyes, skin and lungs. Always observe industry guide-

lines and safety precautions when working with equipment that generates ozone.

Summary of Contents for 10000V





















Reviews: