background image

Note: the above figures are only intended to be a simple 

diagram of the appliance and may not correspond to the 

appearance of the units that have been purchased.

OUTDOOR UNIT

No. Description

1

Air outlet grille

2

Valve

TECHNICAL DATA

GENERAL INFORMATION

Electrical data

Electricity supply

mm

2

Refrigerant gas

R410 A

Size and clearance

H

Minimum power cord section

Fuse or air switch

30

A

Warning

 

 

4.0

mm

mm

mm

MOD

L

W

GWHD(28)ND3CO

950

420

840

        

The temperature of refrigerant circuit will be high,please keep the 

 

 

interconnection cable away from the copper tube.

NAMES OF THE PARTS

Maximum cooling
Minimum cooling
Maximum heating
Minimum heating

Outdoor side DB/WB(

)

43/26(T1)

21/-

24/18

-5/-6

OUTDOOR UNIT WORKING TEMPERATURE RANGE

GENERAL INFORMATION

1

2

GENERAL INFORMATION

3

220-240V

 

60

 

Hz

GWHD(28)ND3AO

1

2

L

W

H

Be sure to cut off the power supply before cleaning the air conditioner; 

otherwise electric shock might happen. 
Wetting of air conditioner may cause the risk of electric shock. Make
sure not to wash your air conditioner in any case.

Volatile liquids such as thinner or gasoline will cause damage to the 
appearance of air conditioner. (Only use soft dry cloth moist cloth clean
the air conditioner cabinet).

Do not dispose this product as unsorted municipal waste. 
Collection of such waste separately for special treatment 
is necessary.

 

If the supply cord is damaged, it must be replaced by the manufacturer
or its service agent or a similarly qualified person in order to avoid a hazard.

Summary of Contents for GWHD(28)ND3AO












Reviews: