background image

16

Installation service- Notices for installation

Important Notices

1. The unit installation work must be done by qualified personnel according to the local

 rules 

and this manual.

Basic Requirements For Installation Position

Install in the following place may cause malfunction. If it is unavoidable contact with 

service center please:

Place where strong heat sources, vapors, flammable gas or volatile objuct are emitted

.

Place where high-frequency waves are generated by radio equipment, welders and 
medical equipment.
Place where a lot of salinities such as coast exists.

Place where the oil (machine oil) is contained in the air.

Place where a sulfured gas such as the hot spring zones is generated.

Other place with special circumstance.

Indoor Unit Installation Position Selection

1. The air inlet and outlet vent should be far from the obstruction, make sure that the air

 can 

be 

blown through the whole room.

2. Select a position where the condensing water can be easily drained out, and the place

 is 

easily connected for outdoor unit.

3. Select a location where the children can not reach.

4. Can select the place where is strong enough to withstand the full weight and vibration of

the unit. And will not increase the noise.

5. Be sure to leave enough space to allow access for routine maintenance. The height of the

installed location should be 2

5

0 cm or more from the floor.

6. Select a place about 1m or more away from TVset or any other electric appliances.

7. Select a place where the filter can be easily taken out.

8. Make sure that the indoor unit installation should accord with installation dimension 

diagram requirements.

2. If the air conditioner has not plug, directly connect it into the fixed circuit, a breaker should be

installed in the fixed circuit. all pole of this breaker should be switching off and the distance
of the contact should be at least 3mm.

Summary of Contents for 66129903294




























Reviews: