manualshive.com logo in svg

AirLive WN-151ARM, User Manual

Share
Download
AirLive WN-151ARM User Manual Download Page 115

 

AirLive WN-151ARM User’s Manual 

115

 

 

PPTP 

Point-to-Point Tunneling Protocol: A VPN protocol developed by PPTP Forum.    With PPTP, users can dial in 

to their corporate network via the Internet.    If users require data encryption when using the Windows PPTP 

client, the remote VPN server must support MPPE (Microsoft Point-To-Point Encryption Protocol) encryption.   

PPTP is also used by some ISP for user authentication, particularly when pairing with legacy Alcatel / 

Thomson ADSL modem. 

 

Preamble Type

 

Preamble are sent with each wireless packet transmit for transmission status. Use the long preamble type for 

better compatibility. Use the short preamble type for better performance 

 

Rate Control

 

Ethernet switches' function to control the upstream and downstream speed of an individual port. Rate Control 

management uses "Flow Control" to limit the speed of a port. Therefore, the Ethernet adapter must also have 

the flow control enabled. One way to force the adapter's flow control on is to set a port to half-duplex mode.

 

 

RADIUS

 

(Remote Authentication Dial-In User Service)

   

An authentication and accounting system used by many Internet Service Providers (ISPs). When you dial in 

to the ISP, you must enter your username and password. This information is passed to a RADIUS server, 

which checks that the information is correct, and then authorizes access to the ISP system. Radius typically 

uses port 1812 and port 1813 for authentication and accounting port. Though not an official standard, the 

RADIUS specification is maintained by a working group of the IETF. 

 

Receiver Sensitivity

 

Receiver sensitivity means how sensitive is the radio for receiving signal. In general; the slower the 

transmission speed, the more sensitive the radio is. The unit for Receiver Sensitivity is in dB; the lower the 

absolute value is, the higher the signal strength. For example, -50dB is higher than -80dB.

 

 

RJ-45

 

Standard connectors for Twisted Pair copper cable used in Ethernet networks. Although they look similar to 

standard RJ-11 telephone connectors, RJ-45 connectors can have up to eight wires, whereas telephone 

connectors have only four. 

 

Router

 

An IP sharing router is a device that allows multiple PCs to share one single broadband connection using NAT 

technology. A wireless router is a device that combines the functions of wireless Access Point and the IP 

sharing router. 

 

Summary of Contents for WN-151ARM
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands