manualshive.com logo in svg

AirLive ARM-104 V3, User Manual

Share
Download
AirLive ARM-104 V3 User Manual Download Page 71

 

AirLive

 

ARM-104_v3

 ADSL2/2+ Router

 

65

 

4.3.2.1.5 LAN Configuration – Use The Following Static IP Address 

 

Use the following Static IP address:

 The following configuration screen will pop-up.   

 

Click the radio button to select 

Enable DHCP Server

 or 

Enable DHCP Relay

 or 

Server and Relay Off

. 

Manually enter the necessary items based on each selection. 

 

 

 

„

 

IP Address:

 The 

ARM-104_v3

 ADSL2/2+ Router’s default IP address is 192.168.1.1. 

„

 

Netmask:

 The 

ARM-104_v3

 ADSL2/2+ Router’s default subnet mask is 255.255.255.0. This 

subnet will allow the gateway to support 254 users. If you want to support a larger number of users 

you can change the subnet mask. The DHCP server is defaulted to only give out 255 IP addresses. 

Remember that if you change your 

ARM-104_v3

 ADSL2/2+ Router’s IP address and you have 

DHCP enabled, the DHCP configuration must reside within the same subnet 

„

 

Default Gateway: 

The default gateway is the routing device used to forward all traffic that is not 

addressed to a station within the local subnet. Your ISP will provide you with the default gateway 

Address.  

„

 

Host Name:

 Can be any alpha-numeric expression that does not contain spaces.   

„

 

Domain:

 Used in conjunction with the host name to uniquely identify the gateway.   

„

 

Enable DHCP Server:

 Click the radio button to enable the DHCP Server. By default, your 

ARM-104_v3

 ADSL2/2+ Router has DHCP server (LAN side) enabled. If you already have a 

DHCP server running on your network, you must disable one of the two DHCP servers; if you plug 

Summary of Contents for ARM-104 V3





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands