manualshive.com logo in svg

AirLive ARM-104 V3, User Manual

Share
Download
AirLive ARM-104 V3 User Manual Download Page 7

 

AirLive

 

ARM-104_v3

 ADSL2/2+ Router

 

1

 

Chapter 1 Introduction 

 

Congratulations on your purchase of this outstanding 

AirLive

 

ARM-104_v3

 ADSL2/2+ Router. This device is 

a Four Ports Ethernet ADSL2/2+ Router combines an “Always-On” high speed Asymmetric Digital Subscriber 

Line (ADSL/ADSL2/ADSL2+) connection to the Telephone Line, and four 10/100BASE-T Ethernet Switch 

connection to a host PC or other Ethernet device to enable the widest array of host connectivity. This 

ARM-104_v3

 ADSL2/2+ Router is specially designed for residential, industries and SOHO users. 

 

ADSL2/2+ is a transmission technology used to carry user data over a single twisted-pair line between the 

Central Office and the Customer Premises. The downstream data rates can go up to 24 Mbps and the 

upstream data rates can go up to 1Mbps with length reach up to 22Kft. This asymmetric nature lends itself to 

applications such as Internet access and video delivery. 

 

With minimum setup, you can install and use the router within minutes. 

Summary of Contents for ARM-104 V3





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands