background image

Safety Warnings

Fluids under high pressure from spray or leaks can penetrate the skin and cause extremely serious  

 

injury, including the need for amputation.

•   NEVER 

point the spray gun at anyone or any part of the body.

•   NEVER

 

put hands or fingers over the spray tip. Do not use a rag or any other material over your fingers. Paint will  

 

    penetrate through material and into the hand.

•   NEVER

 try to stop or deflect leaks with your hand or body.

•   NEVER 

try to "blow back" paint, this is not an air spray sprayer.

•   ALWAYS

 have gun tip guard in place when spraying.

•  

ALWAYS

 

lock gun trigger when you stop spraying.

•   ALWAYS

 remove tip from the gun to clean it.

•   ALWAYS

 follow the 

PRESSURE RELIEF

 

PROCEDURE

, as shown on

 

page 10, before cleaning or removing the  

 

    spray tip or servicing any system equipment. 

•   ALWAYS

 Be sure equipment safety devices are operating properly before each use.

•   ALWAYS

 tighten all fluid connections before each use.

 MEDICAL TREATMENT

If any fluid appears to penetrate your skin, get EMERGENCY CARE AT ONCE.  DO NOT TREAT AS A SIMPLE CUT.

* Go to an emergency room immediately.
* Tell the doctor you suspect an injection injury.
* Tell him what kind of material you were spraying with and have him read NOTE TO PHYSICIAN.

      

 

HIGH PRESSURE SPRAY CAN CAUSE EXTREMELY SERIOUS INJURY.

OBSERVE ALL WARNINGS. 

MEDICAL ALERT - Airless Spray Wounds   

NOTE TO PHYSICIAN: 

          If any fluid appears to penetrate your skin, get   

Injection in the skin is a traumatic injury. 

EMERGENCY MEDICAL CARE AT ONCE. DO 

It is important to treat the injury

 surgically 

NOT TREAT AS A SIMPLE CUT

. Tell the doctor 

as soon as possible. 

DO NOT DELAY

 treatment

exactly what fluid was injected.  Have him read 

to research toxicity. Toxicity is a concern with 

the following "NOTE TO PHYSICIAN". 

 

some exotic coatings injected directly into the

   

 

 

 

 

 

bloodstream. 

Consultation with a plastic surgeon or  

 

 

 

 

 

 

 

reconstructive hand surgeon may be advisable.

INJECTION HAZARD

 GENERAL PRECAUTIONS

•   NEVER

 alter equipment in any manner.                                

•  NEVER

 smoke while in spraying area.

•   NEVER

 spray highly flammable materials.                           

•  NEVER

 use around children.

•   NEVER

 allow another person to use sprayer unless they are thoroughly instructed on safety use and  

 

 

    given this operators manual to read.

•   ALWAYS

 wear a spray mask, gloves and protective eye wear while spraying. 

•   ALWAYS

 ensure fire extinquishing equipment is readily available and properly maintained.

NEVER LEAVE SPRAYER UNATTENDED WITH PRESSURE IN THE SYSTEM. 

FOLLOW PRESSURE RELIEF PROCEDURES ON PAGE 10.

3   

Summary of Contents for Spray & Stripe 3600

































Reviews: