AIREDALE Ultima Remote Air Cooled Installation, Operating And Maintenance Manual Download Page 26

Page: 26 / 40

ULTIMA REMOTE AIR COOLED

Chillers

Installation & Maintenance : 6259535 IM E 02/2013

Controls

VIEWING UNIT OPERATING STATUS

Status Menu

Allows access to view operating status of Digital and Analogue Inputs and Outputs.

Using the

Navigation

instructions, the following

Sub-Menus

shown in sequence can

be accessed:

Digital Inputs

ID1

Phase Rotation (Optional) or MCCB status

ID2

Emergency Stop

ID3

Evaporator Flow Switch

ID4

Remote On/Off (Optional)

ID5

Compressor 1 Contactor Status

ID6

Compressor 2 Contactor Status

ID7

Compressor 3 Contactor Status

ID8

Compressor 4 Contactor Status

ID9

Circuit 1 Low Pressure Switch

ID10

Circuit 2 Low Pressure Switch

ID11

Pump 1 Contactor Status (Optional) or Remote Pump Interlock

ID12

Pump 2 Contactor Status (Optional)

ID13

Remote Pump On/Off (Optional)

ID14

Remote Summer/Winter Or Night Setback (Optional)

ID15

Not Used

ID16

Not Used

ID17

Compressor 5 Contactor Status

ID18

Compressor 6 Contactor Status

Analogue Inputs

Standard

Circuit 1 Liquid Pressure

Circuit 2 Liquid Pressure

Circuit 1 Suction Pressure (Not connected with EEV option) or Leak Detector

Return Water Temperature

Supply Water Temperature

Circuit 2 Suction Pressure (Not connected with EEV option) or Leak Detector

Chilled Water Differential Pressure (Optional)

Remote Setpoint Adjustment or Condenser Water Inlet

Evaporator Inlet Water or Coil 1 Temperature

B10

Ambient or Coil 2 Temperature

Analogue Inputs

Fitted with Electronic Expansion Valve Option (EEV)

Circuit 1 & Circuit 2 Suction Temperature

Circuit 1 & Circuit 2 Suction Pressure

Digital Outputs

NO1

Compressor Contactor 1

NO2

Compressor Contactor 2

NO3

Pump 1 Contactor (Optional)

NO4

Compressor Contactor 3

NO5

Compressor Contactor 4

NO6

Pump 2 Contactor (Optional)

NO7

Circuit 1 Condenser Coil Valve 1

NO8

Circuit 1 Condenser Coil Valve 2

NO9

Circuit 2 Condenser Coil Valve 1

NO10

Circuit 2 Condenser Coil Valve 2

NO11

Not Used

NO12

Alarm Circuit 1

NO13

Alarm Circuit 2

NO14

Circuit 1 Reversing Valve

NO15

Circuit 2 Reversing Valve

NO16

Supplementary Heat

NO17

Compressor 5 Contactor

NO18

Compressor 6 Contactor

Analogue Outputs

Not Used

Circuit 1 & 2 Condenser Fan Speed Controller (Modulated Head Pressure Control)

Circuit 2 Condenser Fan Speed Controller (Modulated Head Pressure Control)

Summary of Contents for Ultima Remote Air Cooled









































Search results

Summary of Contents for Ultima Remote Air Cooled

Reviews:

Related manuals for Ultima Remote Air Cooled

Brands by name

Popular brands

AIREDALE Ultima Remote Air Cooled, Installation, Operating And Maintenance Manual

Search results

Summary of Contents for Ultima Remote Air Cooled

Reviews:

Related manuals for Ultima Remote Air Cooled

Brands by name

Popular brands