Aircel ABP Series Installation & Operation Manual Download

Page: 12 / 52

ABP Series |

Blower Purge Desiccant Air Dryer

INSTALLATION

Lifting Information

Failure to life the unit correctly can result in severe personal

injury or property damage. Use appropriate lifting equipment

and adopt all safety precautions needed for moving and

handling the equipment.

A forklift or crane is recommended for unloading and

installation.

Lift unit by lifting lugs and frame only. Do not lift by piping.

1. Use all lifting points provided. Special care must be used

when lifting the dryer to prevent tip-over.

2. Use clevis connectors, not hooks, on lifting slings.
3. Only lift unit under support frame/base by using the fork

lifting lugs. Do not lift by piping.

4. Check the approximate weight provided on the

specification control drawing to ensure adequate crane or

lift truck capacity.

5. Allow only qualified operators to lift the equipment.
6. Refer to applicable OSHA regulations and local codes

when using cranes, forklifts, and other lifting equipment.

Installation Codes and Procedures

This product should be operated only from the type of power

source specified. If unsure of the type of power supply for

the desired outlet, consult a local power company. Failure to

comply may result in personal injury and/or property damage.

Follow proper lock out/tag out procedures before performing

service or maintenance work.

Electrical installation must be performed by a qualified

electrician and comply with all applicable national and local

codes.

1. Safe and efficient operation of the unit depends on

proper installation.

2. Authorities with jurisdiction should be consulted before

installing to verify local codes and installation procedures.

In the absence of such codes, install unit according to the

National Electric Code and NFPA No. 70-latest edition.

3. A qualified installation and service agent versed in all

regulatory codes must complete installation of this unit.

4. All shipping materials, including shipping covers, must be

removed from the unit prior to, or during unit installation.

Summary of Contents for ABP Series





















































Search results

Summary of Contents for ABP Series

Reviews:

Related manuals for ABP Series

Brands by name

Popular brands

Aircel ABP Series, Installation & Operation Manual

Search results

Summary of Contents for ABP Series

Reviews:

Related manuals for ABP Series

Brands by name

Popular brands