Aircel ABP Series Installation & Operation Manual Download Page 5

Page: 5 / 52

Blower Purge Desiccant Air Dryer

ABP Series

Notice:

For optimum performance, use only Aircel replacement parts.

Notice:

For information and notes specific to custom designed and built dryers, reference the drawing package

provided with the unit. See warranty on manual back cover for custom engineered products.

NOTICE

Throughout this manual, signal words are present to advise of safety

precautions and/or standard practices. Obey these signal words as defined
below:

DANGER!

- Indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING!

- Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION!

- Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury.

Notice: used to address practices not related to personal injury.

WARNING!

GENERAL SAFETY PROCEDURES:

•

Improper installation, operation, or maintenance may contribute to conditions in the work area or facility that could

result in personal injury and product or property damage. Check that all equipment is properly selected and sized for

the intended use.

•

Consult and comply with national and local codes relating to fire or explosion and all other appropriate codes when

determining the location and operation of this equipment.

•

Safe and efficient operation of the unit depends on proper installation.

•

Authorities with jurisdiction should be consulted before installing to verify local codes and installation procedures. In

the absence of such codes, install unit according to the National Electric Code, NFPA No. 70-latest edition.

•

A qualified installation and service agent must complete installation and service of this equipment.

•

DO NOT weld on / to pressure vessel or modify it in any way.

•

DO NOT remove, modify, or adjust protective or safety devices.

•

Lock out power supply and depressurize system before performing maintenance or service work.

•

DO NOT operate the equipment with the control panel door open.

Summary of Contents for ABP Series





















































Search results

Summary of Contents for ABP Series

Reviews:

Related manuals for ABP Series

Brands by name

Popular brands

Aircel ABP Series, Installation & Operation Manual

Search results

Summary of Contents for ABP Series

Reviews:

Related manuals for ABP Series

Brands by name

Popular brands