Aira HCV Installation, Startup, Operation, Service & Maintenance Manual Download Page 23

Page: 23 / 26

COMMISSIONING REPORT

HCV & HCVR Evaporative Cooling & Gas Heating

Page 23 of 26

COMMISSIONIN G REPORT

AIRA COMMISSIONING TEST HCV

Project Name

Project Number

Tag No.

Model No.

Serial No.

Attendees

Fan Test

Y/N

Comments

Is system operating or is this initial start?

Is the overall installation appears correct to gas
codes & manufactures specifications?

Is there any drag when fan is rotated?

Fan has correct rotation

Drive belt tension correct

Is there any unusual vibration? (Check throughout
fan range if variable speed)

Is there any unusual noise?

Is there any bearing noise ?

Is there any motor over-heating?

Check dampers open and close smoothly

Do the control dampers function as units
specifications?

Belt tension checked after operations

Design fan RPM:

Measured RPM:

Design amp Draw

Measured

Amp Draw

Motor

Contactor overloads set at

Low

High

Controls Test

Y/N

Comments

Main control switch plate wired correctly

Check thermostat wired correctly

Auto fan switch set at 40 c / 60 c (Honeywell L4064)
Campini 60c

High limit switches set at 100 c (Honeywell L4064)
Campini 85c Fixed no adjustment.

Summary of Contents for HCV



























Search results

Summary of Contents for HCV

Reviews:

Related manuals for HCV

Brands by name

Popular brands

Aira HCV, Installation, Startup, Operation, Service & Maintenance Manual

Search results

Summary of Contents for HCV

Reviews:

Related manuals for HCV

Brands by name

Popular brands