manualshive.com logo in svg

Air Live G.DUO, User Manual, Page: 47 / 137

Share
Download
Air Live G.DUO User Manual Download Page 47

4. WISP + AP Mode 

 

 

AirLive G.DUO User’s Manual 

40

 

 

4.4.3 Advance (Wireless Settings) 

Operation Mode -> Setup -> Advance 

 

 

 

 

„

 

Fragmentation: 

When the size of a unicast frame exceeds the fragmentation 

threshold, it will be fragmented before the transmission. It should have a value of 

256-2346 bytes, with a default of 2346.    If you experience a high packet error rate, 

you should slightly decrease the Fragmentation Threshold.   

 

 

„

 

RTS Threshold: 

RTS/CTS frames are used to gain control of the medium for 

transmission. Any unicast (data or control) frames larger than specified RTS threshold 

must be transmitted following the RTS/CTS handshake exchange mechanism. The 

RTS threshold should have a value between 256-2347 bytes, with a default of 

2347

. It 

is recommended that this value does not deviate from the default too much.   

Summary of Contents for G.DUO










































































































































Reviews:

No comments