Air Live G.DUO User Manual Download Page 18

Page: 18 / 137

3. Configuring the G.DUO

AirLive G.DUO User’s Manual

The G.DUO offers many different types of management interface. You can configure

through standard web browser (http), secured web (https), command line (telnet), secured

command shell (SSH), and SNMP management. In this chapter, we will explain G.DUO’s

available management interfaces and how to get into them.

3.1 Important Information

The following information will help you to get start quickly. However, we recommend you

to read through the entire manual before you start. Please note the password and SSID

are case sensitive.

The default IP address is: 192.168.1.254 Subnet Mask: 255.255.255.0

There is no password protection by default. To enable password protection,

please go to “System Configuration -> Password Settings”.

The default SSID for Radio1 is “airlive1”

The default SSID for Radio2 is “airlive2”

The default wireless mode is : WISP + AP mode

Please remember to “Apply Change” for settings to be saved and take effect.

Please remember to “Reboot” the device after all settings are changed.

Please keep the TX output power as low as possible for best performance.

By default, the Telnet and SSH functions are turned off. To enable them, please

go to “System Configuration” -> “System Management” menu.

The Emergency Firmware Recovery only works when you connect to LAN2, LAN3,

or LAN4 port. It will not work on LAN1

By Default, the DHCP server is turned on in WISP+AP and AP mode.

The other modes’ DHCP server are turned off.

When you change the mode to WISP+AP or AP mode, the GDUO’s IP

address might change to 192.168.1.254.

Configuring the G.DUO

Summary of Contents for G.DUO










































































































































Search results

Summary of Contents for G.DUO

Reviews:

Air Live G.DUO, User Manual, Page: 18 / 137

Search results

Summary of Contents for G.DUO

Reviews: