background image

 

 

 

 

Trademarks 

 
All rights reserved. 
OvisLink and OvisLink Logo are registered trademarks of OvisLink Corp. Other product 
names and company names are trademarks or registered trademarks of their respective 
owners.  
 
 

FCC Warning 

 
This equipment has been tested and found to comply with the requirements for a Class A 
digital device, pursuant to Part 15 of the FCC Rules. These requirements are designed for 
reasonable protection against harmful interference when the equipment operating in a 
commercial environment. This equipment can generate and radiate electromagnetic energy 
and, if not installed and used in accordance with this guide, may cause significant 
interference with radio communication. Operation of this equipment in a residential area is 
likely to cause interference to household appliances, in which case the user will be required 
to amend at his or her own expense

 
 

CE Mark Warning 

 
This is a Class A product. In a domestic environment, this product may cause radio 
interference, in which case the user may be required to take adequate preventive measures.

 

 
 

Disclaimer 

 
Contents in this manual are subject to changes without prior notice.

 

 
 
 

About this 

User’s Manual

 

 
 

This 

User’s Manual

 aims at helping users to know the key features of 

Ether-FSH2400N

 

Fast Ethernet Switch

 and to install it in a 

10/100BASE-TX Fast Ethernet Local Area Network (LAN)

Summary of Contents for Ether-FSH2400N



























Reviews: