Aim-TTI MX100Q Instruction Manual Download Page 43

Page: 43 / 46

Page 42

Voltage Programming

Speed MX100QP only:

(Typical figures)

Maximum time required for output to settle within 1% of its total excursion

(for resistive load). Excludes command processing time.

90% Load

No Load

90% Load

No Load

35V 3A
16V 6A
70V 3A
35V 6A

Up
Up
Up
Up

10ms
10ms
25ms
10ms

10ms
10ms
12ms
10ms

Down
Down
Down
Down

60ms
10ms
80ms
20ms

550ms
350ms
850ms
550ms

Output Protection:

Output will withstand an applied forward voltage of up to 50V (O/P1, O/P2),

or 80V (O/P3, O/P4). Reverse protection by diode clamp for reverse

currents up to 3A.

Over-voltage Protection

(OVP) Trip:

Outputs 1&2: 1V to 40V. Output 3&4: 1V to 80V. Output trips off for OVP.

Resolution 100mV. Response time: typically 100us. Accuracy: ± (2% + 0.5V)

Over-current Protection

(OCP) Trip:

Measure-and-compare over-current protection is implemented in firmware.

Output trips off for OCP. Setting resolution: 10mA. Response time: typically

500ms. Accuracy: ± (0.3% + 2digits)

Over-temperature

Protection (OTP) Trip:

The output will be tripped off if a fault or blocked ventilation causes the

internal temperature to rise excessively.

METER SPECIFICATIONS (Each Output)

Voltage/Current Meters

5 digit meters for O/P 1 & O/P2; O/P 3 & O/P 4, 4 digit voltage meters

O/P 3 & O/P 4(70V).

Voltage

Resolution: O/P1, O/P2, O/P3 & O/P4 (35V): 1mV; O/P3 & O/P4 (70V):

10mV

Accuracy: 0.1% of reading ± 2 digits

Current

Resolution: 0.1mA

Accuracy: 0.3% of reading ± 5 digits

Current Meter Averaging User selectable On/Off per output with High, Medium or Low settings
V x A:

O/P1 & O/P2: 5-digits. Resolution 0.001W to 100W, 0.01W above 100W.

O/P3 and O/P4: 5-digits. Resolution 0.01W. Accuracy: 0.5% of reading ±

3 digits

SETTING MEMORY STORES

Stores for Individual

Outputs:

50 store positions for each output. Values stored are Range, Voltage,

Current, OVP and OCP

Stores for All Outputs:

50 store positions operating on all four outputs simultaneously.

Values stored are Range, Voltage, Current, OVP, OCP, Output On/Off,

Current Meter Averaging, Multi-On/Multi-Off Setup

USER INTERFACE

Display:

White on black backlit graphic LCD, 340 x 112 pixels.

Multiple font sizes and graphic icons.

Soft Keys:

Eight illuminated multi-function keys annotated from the display.

Home Screen:

Simultaneous display of meters and settings for all outputs.

Direct access to voltage or current setting for any output.

Individual Screens:

Display of meters and extended settings for an individual output (meters

in larger font). Direct access for all settings for that output.

Numeric Setting:

Floating point numeric entry of voltage, current, OVP or OCP.

Spin Wheel Setting:

Voltage, current and other parameters can be adjusted using the spin

wheel in quasi-analog fashion. Wheel can be disabled.

Menu Screen

System level functions are selected from a scrollable list.

Help Text

Multi-page help text is available for system level functions.

Summary of Contents for MX100Q















































Search results

Summary of Contents for MX100Q

Reviews:

Related manuals for MX100Q

Brands by name

Popular brands

Aim-TTI MX100Q, Instruction Manual

Search results

Summary of Contents for MX100Q

Reviews:

Related manuals for MX100Q

Brands by name

Popular brands