Aim-TTI MX100Q Instruction Manual Download Page 14 | Manualshive

Page: 14 / 46

background image

Page 13

6.5 Setting Over-Voltage and Over-Current protection

OVP/OCP

The power supply offers user adjustable over-voltage protection (OVP) and over-current

protection (OCP). If a voltage is detected that exceeds the OVP level, or a current is detected

that exceeds the OCP level, the output is switched off and the message OVP or OCP is

displayed.
OVP is adjustable between 1V and 40V for outputs 1 and 2, and between 1V and 80V for

output 3 and 4. OCP is adjustable between 0.01A and 7A for outputs 1 and 2, and between

0.01A and 3.5A for output 3 and 4.
Pressing the OVP/OCP soft key

creates a new set of soft keys from

which OVP & OCP values can be

set or turned on or off.
Pressing OVP Set causes the key

to illuminate and makes the OVP

value settable. A new value can be

entered using the numeric keypad or by the spin wheel if enabled. OVP can be turned off by

pressing OVP OFF, and turned back on by pressing OVP On. The previous OVP value is

retained when OVP is off and is displayed in brackets.
Similar capabilities are provided for controlling OCP.
Note that, when set to OFF, the function is not completely disabled but is set to the maximum

value for the output. Thus, if OVP was set to OFF on output 1 and an external voltage greater

than 40V was applied to the terminals, an OVP trip would occur.
More information on using OVP and OCP is provided in section 10.7.

6.6 Setting the Voltage/Current Range

Range

Each output has more than one range. For outputs 1 and 2 the choice is 35V/3A, 16V/6A or

35V/6A. For outputs 3 and 4 the choice is 35V/3A, 70V/1.5A or 70V/3A.
Note that selecting a high power setting may require the disabling of other outputs, see table in

section 1.
Pressing the Range soft key brings

up a menu screen which indicates

the currently selected range and

output with a flashing arrow.
All output ranges can be amended

or disabled from this screen using

the soft keys, select the output with

the up and down arrow soft keys and press the desired range soft key. Pressing the cancel soft

key will return to the output screen and the range will remain unchanged, pressing the OK soft

key will action the changes made.
Note that a change of range can only be made when the output is off. If the output is on, a

message will prompt the user to turn it off.

«
...
12
13
14
15
16
...
»

Summary of Contents for MX100Q















































Reviews:

No comments

Related manuals for MX100Q

Brand: Magpowr Pages: 4

Brand: Earlex Pages: 4

Brand: Fein Pages: 53

Brand: Mafell Pages: 75

Brand: Mafell Pages: 46

Brand: Vaterra Pages: 4

ROTO-TIGER RT-2000

Brand: Airtec Pages: 87

Brand: O'Briens Pages: 12

Brand: Lumberjack Pages: 18

MOVITRANS THM20C

Brand: SEW-Eurodrive Pages: 64

Brand: Gearmore Pages: 14

Brand: jobmate Pages: 16

Brand: BLACKCUBE Pages: 14

Brand: KVT Pages: 87

Brand: Baileigh Industrial Pages: 36

Brand: Wera Pages: 48

Brand: Sealey Pages: 3

Brand: Chicago Pneumatic Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands