manualshive.com logo in svg

Ahlborn ALMEMO 2290-2/3, Operating Instructions Manual

The Ahlborn ALMEMO 2290-2/3 is a state-of-the-art scientific instrument. To ensure seamless operation, you need the Operating Instructions Manual which you can download for free from manualshive.com. This comprehensive manual provides detailed guidelines to maximize the potential of your Ahlborn ALMEMO 2290-2/3, guaranteeing accurate and efficient results.

Share
Download
background image

1. INTRODUCTION

The multifunctional measuring instruments ALMEMO

®

 2290-2/3 

Version 5

   

are instruments from the unique product range of measuring devices that are
all equipped with the ALMEMO

®

 connector system, which has been patented

by Ahlborn GmbH. The intelligent ALMEMO

®

 connector provides important

advantages with regard to the connection of sensors and peripherals as all
parameters are stored in an EEPROM within the connector. As a result, the
programming that usually is necessary for the connection is not required.
All sensors and output modules can be connected to all ALMEMO

®

 measuring

devices in the same way. The operation and programming is identical with all
units. Therefore, all of the ALMEMO

®

 measuring system items listed below are

described, in detail, in a separate ALMEMO

®

 manual that is supplied with every

device:

Detailed description of the ALMEMO

®

 system (manual section 1)

Overview of the device functions and measuring ranges (manual section 2)
All sensors with basic principles, operation, technical data (man. section 3)
The options for connecting existing sensors (manual section 4)
All analogue and digital output modules (manual section 5.1)
The interface module RS232, fiber optics, Centronics (manual section 5.2)
The entire ALMEMO

®

 networking system (manual section 5.3)

All functions and their control via the interface (manual section 6) 
A complete interface command list with all print outputs (manual section 7)

These operating instructions only cover features and controls that are specific
for a certain device. As a result, the sections dealing with the system control
via keyboard will only often provide a note referring to a more detailed
description within the manual (manual section x.x.x).

1.1 Function Range

The multifunctional measuring instrument ALMEMO

®

 2290-2 has one

measuring input with 4 channels for more than 65 measuring ranges, the
ALMEMO

®

 2290-3 has two electrically isolated measuring inputs with up to 8

measuring and two differential channels. Two output sockets allow for
connecting any ALMEMO

®

 output modules, for example, the analogue output,

digital interface, trigger input or alarm contacts. Several devices can be
networked by a simple connection between the devices. For easy operation it
is equipped with a keyboard and an 8½-digit LCD display.
The instruments provide many functions for an optimal evaluation of all
sensors, for a flexible process control and for a universal data output. To avoid
a complicated handling, which could be caused by functions that are not
required, these functions can be activated automatically or manually when
required. A few special functions can only be accessed via interface.

   4

ALMEMO

 2290-2/3  

   Functions

Summary of Contents for ALMEMO 2290-2/3













































Reviews:

No comments

Related manuals for ALMEMO 2290-2/3

ABB SM1000 Installation Instructions Manual preview
SM1000
Brand: ABB Pages: 8
Kathrein MSK 15 Mode D'Emploi preview
MSK 15
Brand: Kathrein Pages: 10
Energic Plus MPD-1007E Manual preview
MPD-1007E
Brand: Energic Plus Pages: 12
Keithley 2651A Quick Start Manual preview
2651A
Brand: Keithley Pages: 18
Gates 507C Manual preview
507C
Brand: Gates Pages: 112
Circutor Wibeee Max Instruction Manual preview
Wibeee Max
Brand: Circutor Pages: 48
Aqualytic AL250T-IR Instruction Manual preview
AL250T-IR
Brand: Aqualytic Pages: 140
Qonnex 2-WIRE EMM.630CT-MID Quick Start preview
2-WIRE EMM.630CT-MID
Brand: Qonnex Pages: 2
PANCONTROL PAN 118 Manual preview
PAN 118
Brand: PANCONTROL Pages: 157
Xylem WTW SensoLyt 900 Operating Manual preview
WTW SensoLyt 900
Brand: Xylem Pages: 12
Ocean Reef GSM Mercury Owner'S Manual & Installation Manual preview
GSM Mercury
Brand: Ocean Reef Pages: 24
Milkotester MASTER Touch Operating Instructions Manual preview
MASTER Touch
Brand: Milkotester Pages: 44
National Instruments NI PXIe-4139 Calibration Procedure preview
NI PXIe-4139
Brand: National Instruments Pages: 24
Ocean Optics CHEM2000-UV-VIS Operating Manual And User Manual preview
CHEM2000-UV-VIS
Brand: Ocean Optics Pages: 42
Righton Retinomax K+Screeen Instructions Manual preview
Retinomax K+Screeen
Brand: Righton Pages: 112
YoloLIV Instream User Manual preview
Instream
Brand: YoloLIV Pages: 18
S.E. International RADIATION ALERT Sentry Manual preview
RADIATION ALERT Sentry
Brand: S.E. International Pages: 8
IFM SM2 00 Series Operating Instructions Manual preview
SM2 00 Series
Brand: IFM Pages: 45

Brands by name

Popular brands

Load more brands