Agria 9600-80 Translation Of The Original Operating Instructions Download Page 60

Page: 60 / 76

6 Troubleshooting and Remedies

Remote-controlled High Grass Rotary Mulcher

agria 9600-80

Fault

Possible cause

Remedy

Page

Warning signal
does not sound
when the motor is
stopped

Ignition is not switched on

Release the EMERGENCY
STOP switch

turn the ignition switch to "I"

Beeper defective

Replace beeper

- agria-Service -

Fuse defective

Replace fuse

Harness defective

Check harness

- agria-Service -

The warning
signal sounds
while the engine
is running

The engine oil pressure is not
OK

Check the engine oil level imme-
diately. Top up engine oil if nec-
essary

however the engine oil level is
OK:

- agria-Service -

Oil pressure switch defective

Replace oil pressure switch

The cans were
not emptied in the
correct order

Error in the fuel system

Close the venting screws on the
can set

Leak rectified

FB = Remote control, BM= See separate operating instructions for engine

Summary of Contents for 9600-80













































































Search results

Summary of Contents for 9600-80

Reviews:

Related manuals for 9600-80

Brands by name

Popular brands

Agria 9600-80, Translation Of The Original Operating Instructions

Search results

Summary of Contents for 9600-80

Reviews:

Related manuals for 9600-80

Brands by name

Popular brands