Agria 0900 041 Original Operating Instructions Download Page 34

Page: 34 / 40

agria

Power Hoe 900 / 900-S

6. Troubleshooting

Observe safety instructions! Have all serious malfunctions on the machine or engine repaired by your
agria workshop. They have the proper tools. Improper repairs can only add to the damage.

Problem

Possible cause

Possible solution

Page

Engine

- Spark plug connector not connected

Connect spark plug connector

does not start

- Speed control lever not in

Move speed control lever to

position CHOKE

position “CHOKE”

23, 24

- Fuel tank empty or poor fuel

Fill fresh fuel

- Fuel line clogged

Clean fuel line

- Defective spark plug

Clean, adjust or exchange spark plug

- Engine too much fuel

Dry and clean spark plug and

(“flooded engine”)

start at full throttle

- Inleaked air due to loose caburetor

Tighten attachment bolts

and suction line

Misfirings in

- Engine running in CHOKE range

Move speed control-lever to position

23, 24

engine

HOEING, if necessary, adjust speed

control

- Loose ignition cable

Fit connector tightly on spark plug,
fix ignition cable retaining device,
fix connector tightly on ignition cable

- Clogged fuel line or poor fuel

Clean fuel line, fill fresh fuel

- Vent opening in fuel tank cap clogged

Exchange fuel tank cap

- Water or dirt in fuel system

Drain fuel and fill fresh fuel

- Air filter clogged

Clean air filter or exchange

- Carburetor misadjusted

Re-adjust carburetor

Excessive

- Low engine oil level

Refill oil immediately

temperature

- Impaired cooling

Clean cooling fan grille,

in engine

clean internal cooling fins

- Air filter clogged

Clean air filter

- Carburetor misadjusted

Re-adjust carburetor

Misfirings

- Short firing intervals

Adjust spark plug

in engine

- Incorrect idle mixture

Adjust carburetor

at high speeds

Engine

- Firing interval too long,

Adjust or replace spark plug

frequently

defective spark plug

stalls

- Carburetor misadjusted

Re-adjust carburetor

in idle

- Air filter clogged

Clean air filter

Summary of Contents for 0900 041









































Search results

Summary of Contents for 0900 041

Reviews:

Related manuals for 0900 041

Brands by name

Popular brands

Agria 0900 041, Original Operating Instructions

Search results

Summary of Contents for 0900 041

Reviews:

Related manuals for 0900 041

Brands by name

Popular brands