background image

2

RULES FOR SAFE OPERATION

The  following  safety  precautions  are  suggested.  This
broadcast spreader is designed, engineered and tested
to offer reasonably safe and effective service, provided
it is operated in strict accordance with these instructions.
Failure  to  do  so  may  result  in  personal  injury.  Always
observe the rules of safe operation.

1.

Do  not  allow  anyone  to  operate  the  broadcast
spreader without proper instructions.

2.

Do  not  permit  children  to  operate  the  broadcast
spreader.

3.

Wear eye and hand protection when handling and
when applying lawn or garden chemicals.

4.

Read the chemical label instructions and cautions
for handling and applying the chemicals purchased
for spreading.

5.

Keep  all  nuts,  bolts  and  screws  tight  to  be  sure
equipment is in safe working condition.

6.

Follow maintenance and lubrication instructions as
outlined in this manual.

LOOK FOR THIS SYMBOL TO POINT OUT
IMPORTANT SAFETY PRECAUTIONS. IT
MEANS -- ATTENTION!  BECOME ALERT!
YOUR SAFETY IS INVOLVED.

Your broadcast spreader carton contains parts as shown on pages 2 and 3.  Identify all parts and lay out
as shown.

CARTON CONTENTS

LOOSE PARTS IN CARTON

1.

Hopper Assembly

2.

Wheel, Drive

3.

Wheel, Idler

4.

Spreader Shield

5.

Braces (2)

6.

Flow Control Rod

7.

Vinyl Hopper Cover

8.

Hopper Screen

9.

Handle Tube (short)

10. Flow Control Arm
11. Handle Tube (long)
12. Leg Stand Tube
13. Flow Control Mount Bracket

Hardware Package (not shown)

1

2

3

4

5

6

7

9

10

11

12

13

8

Summary of Contents for 45-02102-101

















Reviews: