InstructIon MAnuAL for:
drop spreader 27kg walk behind
MoDEL no:
spd27w
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. sAFETY INsTRUCTIONs
IMPORTANT:
pLEAsE REAd THEsE INsTRUCTIONs CAREFULLY. NOTE THE sAFE OpERATIONAL REQUIREMENTs, wARNINGs & CAUTIONs.
UsE THE pROdUCT CORRECTLY ANd wITH CARE FOR THE pURpOsE FOR wHICH IT Is INTENdEd. FAILURE TO dO sO MAY CAUsE
dAMAGE ANd/OR pERsONAL INJURY ANd wILL INVALIdATE THE wARRANTY. pLEAsE KEEp INsTRUCTIONs sAFE FOR FUTURE UsE.
2. spECIFICATION
3. INTROdUCTION
4. AssEMBLY
Model No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . spd27w
capacity (weight) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27kg
capacity (volume) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25ltr
spread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .560mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5kg
Dimensions (W x D x H) . . . . . . . . . . . . . . .740 x 810 x 775mm
Manufactured with a strong tubular steel frame and polyethylene
dispensing hopper. fitted with adjustable feed system to control
feed quantities. Designed to spread in a continuous line providing
a more accurate application. suitable for a variety of horticultural
agents including grit, seed, salt, fertiliser and weed killer.
4.1 Please note that the two wheels are assembled to the axle
differently. the left hand wheel (as seen from the handle side
of the hopper) is free wheeling. the right hand wheel drives the
blades within the hopper. referring to fig.1 assemble the left
hand wheel first by sliding a Ø12mm flat washer (11) onto the
axle followed by a bushing (5). slide a wheel (15) over the
bushing followed by another Ø12mm flat washer (11). Insert
the smaller split pin Ø3mm x 30 (7) through the holes in the
end of the axle and retain the assembly by bending it over.
4.2 slide another washer (11) and bushing (5) over the axle on the
other side of the hopper ensuring that the holes in the bushing
are adjacent to the side of the hopper. slide the other wheel
over the bushing and align the holes in the inner hub of the
wheel with the holes in the bushing and the hole through the
axle. retain this assembly by inserting the larger split pin
Ø5mm x 45 (8) through all three components. retain the
assembly by bending over the split pin.
Original Language Version
sPD27W Issue: 1 - 13/06/11
Before each use, check that there is no damage to the spreader
and that all fixings are tight.
replace or repair damaged parts.
Use only recommended parts.
Unauthorised parts may be dangerous and will invalidate the
warranty.
Ensure that the operator is fully trained and competent to operate
the spreader.
Ensure that all chemical safety instructions are adhered to when
handling products for use in the spreader. A full range of personal
safety equipment is available from your sealey dealer.
Always distribute the load evenly.
Ensure all non essential personnel keep a safe distance when
the spreader is in use.
Keep hands and feet away from moving parts.
dO NOT
overload the spreader - see specification.
dO NOT
leave unattended, especially when loaded.
dO NOT
allow anybody to sit, stand, or ride on the spreader.
dO NOT
allow untrained personnel to use the spreader.
dO NOT
allow children to play in or climb onto the spreader.
dO NOT
use on windy days when spreading seeds or herbicides.
dO NOT
tow this spreader with a motorized vehicle of any sort.
dO NOT
use the spreader for purposes other than for which it is
designed.
dO NOT
operate the spreader when you
are tired or under the
influence of alcohol, drugs or intoxicating medicines.
When loaded,
dO NOT
operate the spreader over edges, rough
surfaces etc. where the spreader is at risk of overturning.
wARNING!
failure to comply with these instructions may result
in damage to spreader or other property and/or personal injury.
