background image

6

FIGURE 7

FIGURE 8

19. Hook  free  end  of  flow  control  rod  through  hole  in

slide  gate  bracket  located  near  bottom  of  hopper.
See figure 9.

FIGURE 9

FIGURE 10

16. Assemble  the  flow  control  arm  to  the  flow  control

mounting bracket using a 1/4" x 3/4" hex bolt, two
nylon washers and a 1/4" hex lock nut as shown
in  figure  7. 

Tighten carefully. 

The  flow  control

arm  should  be  snug,  but  should  pivot  with  no
more than a slight resistance.

17. Assemble the vinyl grip. See figure 7.

1/4" x 3/4"

HEX BOLT

1/4" HEX

LOCK NUT

FLOW CONTROL

MOUNTING

BRACKET

FLOW 

CONTROL 

ARM

(2) NYLON

WASHERS

VYNIL GRIP

FLOW

CONTROL

ROD

FLOW 

CONTROL 

LINK

3/32"

COTTER

PIN

5/16" FLAT

WASHER

SLOT

18. Place a 5/16" flat washer onto the end of the flow

control rod. Insert the end of the rod through the
slot  in  the  flow  control  mounting  bracket  and
through the hole in the flow control link. Secure
with a 3/32" x 3/4" cotter pin. See figure 8.

20. Assemble both the flow control mounting bracket

and the short handle tube to the long handle tube
using two 1/4" x 1-3/4" hex bolts, four 5/16" flat
washers  and  two  1/4"  hex  lock  nuts.

 Do not

tighten at this time. 

See figure 10.

21. Place a handle grip on each handle. See figure

10.

1/4" x 1-3/4"
HEX BOLT

1/4" HEX
LOCK NUT

HANDLE
TUBE
(SHORT)

HANDLE
TUBE
(LONG)

HANDLE GRIP

FLOW CONTROL 
MOUNTING BRACKET

5/16"

FLAT

WASHERS

HOPPER

SLIDE
GATE
BRACKET

FLOW
CONTROL
ROD

Summary of Contents for 45-02102-101

















Reviews: