background image

5

16. Turn the cart upside down. Place the handle tube

on  the  bottom  of  the  cart  as  shown  in  figure  10.
Place the four tube clamps over the handle tube,

with the longer leg of each tube clamp to the
outside. 

Secure  the  four  tube  clamps  over  the

handle tube using eight 1/4" x 1" screws, eight flat
washers and eight hex nuts. Make only finger tight
until all eight screws are in place and then 

tighten

securely

. See figure 10.

The length of the handle tube can be
adjusted by sliding the tube in or out
before tightening the four clamps. See
figure 10.

NOTE

FIGURE 10

17. Insert a 1/4" x 1" screw through the hole at the rear

of each side panel and the hole at the rear of each
side angle. Secure with 1/4" flat washers and 1/4"
hex nuts, 

making only finger tight at this time.

See figure 11.

18. Place the tube caps on the ends of the "W" shaped

leg tube. See figure 11.

19. With the cart still upside down, assemble the leg

tube  to  the  bottom  of  the  cart.  Line  up  the  two
holes in the center of the leg tube with the holes in
the bottom of the cart. Secure the leg tube to the
bottom of the cart with two 1/4" x 2" screws, 1/4"
flat washers and 1/4" hex nuts. 

Make only finger

tight at this time.

 See figure 11.

20. Attach the leg tube to the side panels with four 1/4"

x 2" screws, 1/4" flat washers and 1/4" hex nuts.

Make only finger tight at this time.

  See  figure

11.

21. Fasten the support straps to the leg tube with two

1/4"  x  1-1/2"  screws,  1/4"  flat  washers  and  1/4"
hex nuts. See figure 11.

22. At this time 

tighten securely

 all screws and nuts

assembled in figure 11.

FIGURE 11

For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

Summary of Contents for 45-01772









Reviews: