background image

3

 GENERAL SAFETY INSTRUCTIONS

WARNING! Read all safety warnings and all instructions

. Failure to follow the warnings and 

instructions may result in electric shock, fire and/or serious injury. 

Save all warnings and instructions for future reference.

 The term “power tool” in the warnings refers 

to your mainsoperated (corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a.   Keep work area clean and well lit. 

Cluttered or dark areas invite accidents.

b.  Do not operate power tools in explosive atmospheres, such as in the presence of flammable 

liquids, gases or dust.

 Power tools create sparks which may ignite the dust or fumes.

c. 

Keep children and bystanders away while operating a power tool. 

Distractions can cause you to 

lose control.

2) ELECTRICAL SAFETY

a.  Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any 

adapter plugs with earthed (grounded) power tools.

 Unmodified plugs and matching outlets will 

reduce risk of electric shock.

b.  Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and 

refrigerators.

 There is an increased risk of electric shock if your body is earthed or grounded.

c. 

Do not expose power tools to rain or wet conditions.

 Water entering a power tool will increase the 

risk of electric shock.

d.  Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. 

Keep cord away from heat, oil, sharp edges or moving parts. 

Damaged or entangled cords 

increase the risk of electric shock.

e. 

When operating a power tool outdoors, use an extension cord suitable for outdoor use. 

Use of a 

cord suitable for outdoor use reduces the risk of electric shock.

f. 

If operating a power tool in a damp location is unavoidable, use an earth leakage circuit 
breaker.

 Use of an earth leakage circuit breaker reduces the risk of electric shock.

3) PERSONAL SAFETY

a.  Stay alert, watch what you are doing and use common sense when operating a power tool. Do 

not use a power tool while you are tired or under the influence of drugs, alcohol or medication.

 

A moment of inattention while operating power tools may result in serious personal injury.

b.  Use personal protective equipment. Always wear eye protection.

 Protective equipment such as 

dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will 
reduce personal injuries.

c. 

Prevent unintentional starting. Ensure the switch is in the off-position before connecting to 
power source and/or battery pack, picking up or carrying the tool.

 Carrying power tools with 

your finger on the switch or energising power tools that have the switch on invites accidents.

d.  Remove any adjusting key or wrench before turning the power tool on. 

A wrench or a key left 

attached to a rotating part of the power tool may result in personal injury.

e. 

Do not overreach. Keep proper footing and balance at all times. 

This enables better control of the 

power tool in unexpected situations.

f. 

Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away 
from moving parts.

 Loose clothes, jewelry or long hair can be caught in moving parts.

g.  If devices are provided for the connection of dust extraction and collection facilities, ensure 

these are connected and properly used.

 Use of dust collection can reduce dust-related hazards.

Summary of Contents for Compound Miter Saw

















Reviews: