Agora Models STEVE MCQUEEN'S ICONIC PORSCHE 917KH Pack 05 Build Instructions Download Page 13

Page: 13 / 59

AGORA

MODELS

STAGE 30: FITTING THE BRAKES,

STEERING AND FRONT SUSPENSION

S T E P 3

Fit the

left brake

caliper (30A), marked

with an ‘L’, onto the

hub carrier (3G) and

fix it in place using two

IM screws.

Attach one of the

brake piston covers

(30B) to the left brake

caliper (30A) by

pressing the two small

pins on the cover into

the corresponding

holes on the caliper.

Make sure that the

cover is oriented the

correct way as shown

in the image, following

the curve of the brake

caliper.

S T E P 4

Next take the

right brake disc outer surface (30E) and remove the backing paper (blue arrow).

Stick it to the

brake disc rotor (outer half) (30G) using the adhesive side. Take note of the

direction of the ventilation holes (red arrow). Ensure the outer holes align with the ribs of the disc

(orange arrows).

Summary of Contents for STEVE MCQUEEN'S ICONIC PORSCHE 917KH Pack 05




























































Search results

Summary of Contents for STEVE MCQUEEN'S ICONIC PORSCHE 917KH Pack 05

Reviews:

Related manuals for STEVE MCQUEEN'S ICONIC PORSCHE 917KH Pack 05

Brands by name

Popular brands

Agora Models STEVE MCQUEEN'S ICONIC PORSCHE 917KH Pack 05, Build Instructions

Search results

Summary of Contents for STEVE MCQUEEN'S ICONIC PORSCHE 917KH Pack 05

Reviews:

Related manuals for STEVE MCQUEEN'S ICONIC PORSCHE 917KH Pack 05

Brands by name

Popular brands