Agora Models STEVE MCQUEEN'S ICONIC PORSCHE 917KH Pack 05 Build Instructions Download Page 1

Page: 1 / 59

Porsche, the Porsche shield and the distinctive design of Porsche cars are trademarks and trade dress of Porsche AG. Permission granted.

Personality rights of Steve McQueen are used with permission of Chadwick McQueen and The Terry McQueen Testamentary Trust.

Represented exclusively by Greenlight.

Pack 05

B U I L D I N S T R U C T I O N S

STAGE 29: INSTALLING THE

FRONT RIGHT SUSPENSION

STAGE 30: FITTING THE BRAKES,

STEERING AND FRONT SUSPENSION

STAGE 31: ADDING THE LEFT COCKPIT

TUBULAR FRAME TO THE CHASSIS

STAGE 32: ATTACHING THE LEFT FUEL TANK

WITH THE CIRCUIT BOARD

STAGE 33: ATTACHING THE RIGHT FUEL TANK

AND CABLES

STAGE 34: ADDING THE RIGHT COCKPIT

TUBULAR FRAME TO THE CHASSIS

STAGE 35: FIXING THE MUDGUARDS AND

ADDING THE ELECTRICAL CABLES

STAGE 36: ASSEMBLING AND ATTACHING

THE RIGHT FRONT WHEEL

STAGE 37: FITTING THE COCKPIT PARTITION

FRAME AND THE OIL HOSES

Summary of Contents for STEVE MCQUEEN'S ICONIC PORSCHE 917KH Pack 05




























































Search results

Summary of Contents for STEVE MCQUEEN'S ICONIC PORSCHE 917KH Pack 05

Reviews:

Related manuals for STEVE MCQUEEN'S ICONIC PORSCHE 917KH Pack 05

Brands by name

Popular brands

Agora Models STEVE MCQUEEN'S ICONIC PORSCHE 917KH Pack 05, Build Instructions

Search results

Summary of Contents for STEVE MCQUEEN'S ICONIC PORSCHE 917KH Pack 05

Reviews:

Related manuals for STEVE MCQUEEN'S ICONIC PORSCHE 917KH Pack 05

Brands by name

Popular brands