Agora Models FDNY FIRE TRUCK TOWER LADDER 9 Build Instructions Download Page 13 | Manualshive

Page: 13 / 34

background image

AGORA

MODELS

13

17

19

18

20

Stage 59: Assembling the Boom Support

and Attaching the Main Body to the Chassis

Prepare to fix the storage cupboard assembled in stage 58 to
the turntable. Locate the fixing points on the bottom of the
cupboard and align them with the 2 holes on the turntable
(circled). Place in position.

This is how your turntable should now look.

Flip the turntable over and secure the cupboard from the
underside using 2 x Type C screws.

Push the hose connector into the circular recess on the
turntable.

2 x Type C

«
...
11
12
13
14
15
...
»

Summary of Contents for FDNY FIRE TRUCK TOWER LADDER 9



































Reviews:

No comments

Related manuals for FDNY FIRE TRUCK TOWER LADDER 9

Brand: FG Modellsport Pages: 28

Brand: Jamara Pages: 4

Brand: JIN YOW Pages: 14

Brand: Duratrax Pages: 16

Brand: REVELL Pages: 8

Brand: Carrera RC Pages: 11

Brand: Jamara Pages: 4

Brand: Jamara Pages: 24

Brand: ABC Hobby Pages: 12

Brand: Serpent Pages: 12

Brand: Serpent Pages: 20

Brand: Kobalt Pages: 52

TRAIL FINDER 2 RTR

Brand: RC4WD Pages: 18

Brand: KID Trax Pages: 24

Brand: Jamara Pages: 16

Bagger J-Matic 2,4 GHz

Brand: Jamara Pages: 4

Brand: RCm Pages: 34

Ferrari FXX K Evo 2,4GHz

Brand: Jamara Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands