AGM Global Vision VICTRIX User Manual Download Page 20 | Manualshive

Page: 20 / 36

AGM Global Vision VICTRIX User Manual Download Page 20

20

AGM Global Vision

2.2.4 MAIN MENU

NOTE

Enter the main menu with a long press of the Up button. Press the Left/Right buttons to select

between the main menu options.

All menu is displayed in the central area of the image. The reason is the reduced field of view of

the day sight by higher magnifications. Reaching a low battery state the device gives a warning in

the top left corner of the central area.

EXIT

Press the Up/Down button to Exit, the Main Menu will not disappear automatically.

AUTO NUC

Press the Up/Down button to turn Automatic Non-Uniformity Calibration On / Off. In the

automatic mode the need for calibration is based on software algorithm, calibration starts

automatically. When choose Off, user will do calibration manually by either lens cover(silent

without shutter) or press middle button(with shutter). Manual calibration function is in

Quick Menu.

OLED BRIGHTNESS

Press the Up / Down buttons to change LED brightness from 0, 1, 2.

UNIT

Press Up/Down to select units of measurement from Yards and Meters.

DEFECTIVE PIXEL REPAIR

Press Up/Down buttons then close lens cover to repair defective pixel. Defective pixels are

found by software algorithm.

«
...
18
19
20
21
22
...
»

Summary of Contents for VICTRIX





































Reviews:

No comments