manualshive.com logo in svg

Agilent Technologies SureCycler 8800, Setup And User Manual

Share
Download
Agilent Technologies SureCycler 8800 Setup And User Manual Download Page 62

5

Maintenance and Updates

 

Maintenance

62

Agilent SureCycler 8800 Setup and User’s Guide

Maintenance

Cleaning

The SureCycler 8800 is designed to require a minimum amount of 
maintenance by the user. 

•

Use water or isopropyl alcohol to clean the instrument.

•

Do not let organic solvents or aggressive solutions come in contact with 
the instrument. 

•

Do not let liquid enter the instrument. 

•

Turn off and disconnect the instrument from the power supply before 
you clean.

Replacing a fuse

WA R N I N G

Fuse compartments are located on the rear of the instrument, above the 
main power connection. Check the voltage rating label to verify that the 
instrument is compatible with the AC voltage available at the installation 
site. Check that fuses are rated as T 10A, 250V. 

Disconnect the power cord before you remove or install a fuse to avoid the 
possibility of serious injury from electrical shock.

Summary of Contents for SureCycler 8800



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands