manualshive.com logo in svg

Agilent Technologies N4419B, Installation And User Manual, Page: 42 / 44

Share
Download
Agilent Technologies N4419B Installation And User Manual Download Page 42

3-6

 

Safety and Regulatory Information

Safety Information

General 

WARNING

To prevent electrical shock, disconnect the Agilent Technologies 
(N4419B, N4420B, and N4421B) S-parameter test set from mains 
before cleaning. Use a dry cloth or one slightly dampened with 
water to clean the external case parts. Do not attempt to clean 
internally.

WARNING

If this product is not used as specified, the protection provided by 
the equipment could be impaired. This product must be used in a 
normal condition (in which all means for protection are intact) 
only.

CAUTION

This product is designed for use in Installation Category II and Pollution 
Degree 2.

CAUTION

VENTILATION REQUIREMENTS: When installing the product in a 
cabinet, the convection into and out of the product must not be restricted. 
The ambient temperature (outside the cabinet) must be less than the 
maximum operating temperature of the product by 4

°

 C for every 100 watts 

dissipated in the cabinet. If the total power dissipated in the cabinet is 
greater that 800 watts, then forced convection must be used.

Summary of Contents for N4419B













































Reviews:

No comments